03Diagnosing Starter Cranking Problems Tech Tip130006272016
03Diagnosing Starter Cranking Problems Tech Tip130006272016 MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 TRUCK PARTS SUPER STORE TM While cranking problems can be frustrating, identifying and correcting the root cause does not have to be. The first step is to identify the symptoms. In a cranking system, you can divide your symptoms into one of three possible troubleshooting categories: ⢠⢠Slow Crank: The starter will crank, however, the engine RPM is slow to start the vehicle. ⢠⢠Click No-Crank: The solenoid clicks but the starter doesnât crank. ⢠⢠No-Click No-Crank: The solenoid doesnât click and the starter doesnât crank. Once youâve identified which problem youâre dealing with, then you can start to remedy it. For all issues, the initial troubleshooting is the same: you start with the batteries. STEP 1 - Begin at the batteries: Charge the batteries and perform battery load test on the battery bank. If the load test fails, then individually test each battery and replace any faulty ones. STEP 2 - Perform a voltage drop test: Once batteries pass muster, then perform a voltage drop test on the starter main cables. The starter voltage drop should be less than .5V drop total on cranking circuit. This is an important step and is often the cause of a slow cranking complaint. Yet, voltage drop also is a leading cause of click or no- click complaints because almost every vehicle manufacturer uses the heavy positive post, located on the starter solenoid, as a place to pick up the current used to supply the control circuit. STEP 3 - Identify the specific issue: Until now, the diagnostic path has remained the same regardless of the complaint. Now is where you address the specific issue. ⢠⢠Slow Cranking: For the starter to be cranking, the control circuit would have to be working. So, if battery and cable checks are within specification and the vehicle still cranks slowly, then itâs a slow cranking problem and itâs time to replace the starter. ⢠⢠Click No-Crank: Check the control circuit. If the starter does not contain an Integrated Magnetic Switch, or IMS, then a voltage drop test will need to be performed on the vehicle control circuit. If the starter does have an IMS switch function, then the technician will have to verify that the vehicleâs control circuit is providing voltage to the starter IMS. ⢠⢠No-Click No-Crank: When this occurs, power is not being sent to the solenoid, making it very unlikely that the issue is related to the starter motor. Diagnosing Starter Cranking Problems May 24, 2016 (03Diagnosing Starter Cranking Problems Tech Tip) TECH Tips CATALOG NUMBER 03 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ⢠Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==