18Horton Fan Inspection Tech Tip 1. Check for Air Leaks Apply air pressure to the fan drive. Confirm that the vehicle’s air system reservoir and air lines are clean and dry and without restrictions. Check solenoid valve for proper operation. a) Listen for air leaks around the solenoid valve, filter assembly, air lines and fittings. b) Look for air leaks. Using a spray bottle, spray soapy water around the spring housing, sheave and bleed hole. Look for bubbles. Maintenance Procedure: If an air leak is present, repair the fan drive with the appropriate Horton repair kit or replace the fan drive with a remanufactured Horton fan drive or new fan drive. Clean and repair vehicle air system as required. 2. Check the Fan Drive Friction Surfaces Check air pressure to the fan drive. A minimum of 90 psi [6.2 bar] is required to fully disengage the fan drive. a) Inspect the fan drive friction facing for wear by measuring the thickness of the friction facing material. A new friction facing is 11 / 32 inch [8.51 mm] thick. Replace the friction facing material if it has worn to ¼ inch [6.35 mm] thick or smaller. The fan mounting friction disc (FMFD) may need to be removed to check liner wear on the two-speed version. b) Check the FMFD surface for wear, discoloration or other signs of overheating. Maintenance Procedure: - If excess wear is present, check engine control module (ECM) and air-conditioning (AC) runtimes. The fan and AC runtime should be set at 60-90 seconds or greater to reduce friction wear and engagements. - Check ECM programming of engine brake. The engine brake should be set to “Fan Off” when the engine brake is applied. - Check for fan obstruction or shroud interference. 3. Check the Fan Drive for Proper Engagement and Disengagement Set the ignition switch to “On” for the following procedures. But DO NOT start the engine. a) Manually engage and disengage the fan drive by disconnecting the electrical connector at the solenoid valve, opening and closing the solenoid valve. b) Remove the air supply to engage the fan drive by following the instructions above. Attempt to move the fan. If the fan rotates with minimal force, the friction surfaces are worn beyond use. Repair with the appropriate Horton repair kit or remanufactured or new fan drive. c) Check the electrical wiring at the thermal switch, air-conditioning pressure switch and the solenoid valve. Make sure there are no loose wires or connections. Maintenance Procedure: - If excess friction wear is present, repair the fan drive with the appropriate Horton repair kit or remanufactured or new fan drive. - If over-cycling of an on/off fan drive is resulting in excessive friction wear, a Horton DM Advantage ® Two-Speed or PolarForce ® Two-Speed Conversion Kit should be considered to replace an on/off fan drive when making the repair. Inspection Procedures FMFD IRON PULLEY ALUMINUM SPRING HOUSING FRICTION LINER MEASURE THIS DISTANCE TO DETERMINE WEAR and On/Off and Two-Speed Fan Drives and Horton Fans NOTE: All Inspection Procedures to be conducted with the engine off. Recommended 25,000-mile (40,000 Km) or 300-hour Preventive Maintenance (whichever comes first). Check area between pulley and clutch pack for air leaks Check bleed hole for air leaks Check for discoloration or other signs of overheating Inspect friction liner wear Signs of overheating TECH Tips 1. Check for Air Leaks Apply air pressure to the fan drive. Confirm that the vehicle’s air system reservoir and air lines are clean and dry and without restrictions. Check solenoid valve for proper operation. a) Listen for air leaks around the solenoid valve, filter assembly, air lines and fittings. b) Look for air leaks. Using a spray bottle, spray soapy water around the spring housing, sheave and bleed hole. Look for bubbles. Maintenance Proc ure: If an air leak is present, repair the fan drive with the appropriate Horton repair kit or replace the fan drive with a remanufactured Horton fan drive or new fan drive. Clean and repair vehicle air system as required. 2. Check the Fan Drive Friction Surfaces Check air pressure to the fan drive. A minimum of 90 psi [6.2 bar] is required to fully disengage the fan drive. a) Inspect the fan drive friction facing f r wear by measuring the thickness of the friction facing material. A new friction facing is 11 / 32 inch [8.51 mm] thick. Replace the friction facing material if it has worn to ¼ inch [6.35 mm] thick or smaller. The fan mounting fricti disc (FMFD) m y need to be removed to check liner wear on the two-speed version. b) Check the FMFD surface for wear, discoloration or other signs of overheating. Maintenance Procedure: - If excess wear is present, check engine control module (ECM) and air-conditioning (AC) runtimes. The fan and AC runtime should be set at 60-90 seconds or greater to reduce friction wear and engagements. - Check ECM programming of engine brake. The engine brake should be set to “Fan Off” when the engine brake is applied. - Check for f n obstruction or shroud interfere c . 3. Check the Fan Drive for Proper Engagement and Disengagement Set the ignition switch to “On” for the following procedures. But DO NOT start the engine. a) Manually engag and dis ngage the fan drive by disconnecting the electrical connector at the solenoid valve, opening and closing the solenoid valve. b) Remove the air supply to engage the fan drive by following the instructions above. Attempt to move the fan. If the fan rotates with minimal force, the friction surfaces are worn beyond use. Repair with the appropriate Horton repair kit or remanufactured or new fan drive. c) Check the electrical wiring at the thermal switch, air-conditioning pressure switch and the solenoid valve. Make sure there are no loose wires or connections. Maintenance Procedure: - If excess friction wear is present, repair the fan drive with the appropriate Horton repair kit or remanufactured or new fan drive. - If over-cycling of an on/off fan drive is resulting in excessive friction wear, a Horton DM Advantage ® Two-Speed or PolarForce ® Two-Speed Conversion Kit should be considered to replace an on/off fan drive when making the repair. Inspection Procedures FMFD IRON PULLEY ALUMINUM SPRING HOUSING FRICTION LINER MEASURE THIS DISTANCE TO DETERMINE WEAR and On/Off and Two-Speed Fan Drives and Horton Fans NOTE: All Inspection Procedures to be conducted with the engine off. Recommended 25,000-mile (40,000 Km) or 300-hour Preventive Maintenance (whichever comes first). Check area between pulley and clutch pack for air leaks Check bleed hole for air leaks Check for discoloration or other signs of overheating Inspect friction liner wear Signs of overheating CATALOG NUMBER 18 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

17DPF Filters Clamps Gaskets and Bellows CATALOG NUMBER 17 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ DPF Filter and DOC P/N Reference P/N Description/ OE# Clamp P/N Ref Gasket P/N Ref DNX58001 RWRC0001-SA DPF Cummins ISX 4969700NX, 2880168NX, 4969701N DNX65822 HDA100279-006 HDAGSK-02-5231 DNX58817, HDADAWCU001 DNX35002 RWRC0002-SA DPF DD15 RA6804910294, 23537225, RA6804908692, A680 DNX35806 HDA02-8-024-321 HDADAWDD003 DNX35805 RWRC0004-SA DNX58004 DPF ISM 4965244NX, 4352923NX, 4965055D, 4352920NX HDA100279-006 DNX65822 HDAGSK-02-5231 DNX58817, HDADAWCU001 RWRC0006-SA DNX82006 DPF Volvo/Mack D13 20864127, 85000726, 21850658 HDA100279-007 DNX82809 HDAGSK-20-5241 DNX82810 RWRC0009-ID DNX82012 DOC Mack D13 28064129, 85001355, 20864129, 21850645 HDA100279-007 DNX82809 HDAGSK-20-5241 DNX82810 RWRC0014-ID DOC DETROIT DIESEL DD15 RA6804901214 DNX35806 HDA02-8-024-321 HDAGSK-04-0531 HDADAWDD003, DNX35805 RWRC0016-ID DNX58017 DOC ISX 2880259NX, 4936734NX, 2607044C91, 2888262NX, 14.45" Outer Diameter HDA100279-006 DNX65822 HDAGSK-02-5231 HDADAWCU001, DNX58817 - - Two Clamp and Gasket Sizes for RWRC0016-ID, 5.7" Outer Diameter DNX35803 DNX35814 RWRC0028-ID DNX58015 DOC Cummins ISM 4965243NX, 5287191NX HDA100279-006 DNX65822 HDAGSK-02-5231 HDADAWCU001, DNX58817 RWRC0034-ID DNX58042 DOC Cummins 3999660, 3103618, Q619494, Q619723 DNX58825 HDAGSK-02-5711 DNX65821 RWRC0060-ID DNX58025 DOC Cummins ISX 2888249NX, 4969542NX, 4965317NX HDA100279-006 DNX65822 HDAGSK-02-5231 HDADAWCU001, DNX58817 DNX82010 RWRC0064-SA DPF VolvoD13/Mack MP8 21212429, 21212431, 21415912 RWRX12C0-01435-VB DNX82824 HDADAWCT005 DNX82825 RWRC0079-SA DNX65011 DPF Maxxforce 13 2604830C91, 2604046C91, 5010845R1 DNX35820 RWRX12C0-01338-VB DNX35823 DNX65020 RWRC0105-ID DOC Maxxforce 13 2604039C91 DNX35820 RWRX12C0-01338-VB DNX35823 DNX58007 RWRC0023-SA DPF CUMMINS: ISB 4965287; NX,Q612386A, Q621386, A-CE DNX58824 HDAGSK-02-5201 DAWCU005, DNX65831 DNX58019 RWRC0106-ID DOC CUMMINS ISX 2880505N;X, C0A6-ID, C0106-ID HDA100279-006 DNX65822 HDAGSK-02-5231 DNX58817 DPF kits include gaskets and clamps for easy installation! DPF FILTERS, GASKETS, CLAMPS Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15Phillips X Tend Tracker Bar Extension New Day Cab CATALOG NUMBER 15 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ X- TEND Tracker Bar Extension NOW AVAILABLE FOR DAY CABS Prevent cables from banging against the back of the cab. • The ONLY tracker bar extension for day cabs • Extends cables out an additional 8” from the tracker bar • Improve resale value and avoid costly repairs • Decreases driver distraction from the noise of banging cables • Snaps on. No hardware or tools needed! • Stainless steel tubing and eye hook • Non-corrosive mounting and support brackets For new and innovative products, visit www.phillipsind.com 12070 Burke Street, Santa Fe Springs, CA 90670 800.423.4512 CD1074_200717_REV1 X - TEND Tracker Bar Extension NOW AVAILABLE FOR DAY CABS Prevent cables from banging against the back of the cab. • The ONLY tracker bar extensio for day cabs • Extends cables out an additional 8” from the tracker bar • Improve resale value and avoid costly repairs • Decreases driver distraction from the noise of banging cables • Snaps on. No hardware or tools needed! • Stainless steel tubing and eye hook • Non-corrosive mounting and support brackets Part No. 17-35 X-TEND ® Day Cab tra for 3/4" diameter trac Part No. 17-35 X-TEND ® Day Cab tra for 1" diameter track WE MAKE PRODUCTS THAT MAKE A DIFFERENCE ® TEND ® Bar Extension LABLE FOR DAY CABS from banging against the b. bar extension for day cabs ut an additional 8” from the tracker bar lue and avoid costly repairs distraction from the noise of banging cables dware or tools need d! bing and eye hook unting and support brackets Part No. 17-3500 X-TEND ® Day Cab tracker ba r extension for 3/4" diameter tracker bars Part No. 17-3501 X-TEND ® Day Cab tracker bar extension for 1" diameter tracker bars PH 17-3500 X-TEND ® Day Cab Tracker Bar Extension for 3/4" diameter tracker bars PH 17-3501 X-TEND ® Day Cab Tracker Bar Extension for 1" diameter tracker bars ® Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15Butane Torches BUTANE TORCHES & REFILLS CATALOG NUMBER 15 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ P/N KS T-MTC-51 • Plastic canister torch • Self-igniting, Piezo Electronic Ignition System • 2500°F / 1300°C • 120 minutes of continuous use • Refillable • Windproof flame • Hand held or table top • Butane not included BUTANE-POWERED MICROTORCH P/N HDA83-6525 • Hands free - slide lock for continuous use and instant operation • Ergonomic handle design ensures a non-slip grip • Removable base for table-top or hand-held use • 60 minute continuous run time with a full charge • Maximum Temperature Rating: 1300°C (2500°F) • Instant Off safety switch • Adjustable flame: Pin point torch to a heavy duty broad flame • Butane not included TRIGGER TORCH • Best for small jobs and quick repairs • Lifetime waterproof ignition system • Refillable tank provides up to 30 minutes of butane capacity • Adjustable gas flow with wind-proof flame • Protective flip-open cap • See through fuel tank • Child resistance P/N PH 4-054 MINI-JET TORCH P/N ISNMAS51773-24H • For Phillips & NSPA Torches • 5-1/8 oz. ULTRATANE BUTANE Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15Phillips Nylon Cable Wraps Easy to wrap and unwrap combination assemblies Convenient replacement for spiral wrap Protects cables from damage due to harsh weather conditions, chaffing, rubbing and tangling Keeps cables organized NYLON CABLE WRAPS For 3-IN-1 Combination Assemblies PH 5-608 8 Ft. Black Nylon Cable Wrap for 12 Ft. Combination Assemblies PH 5-610 10 Ft. Black Nylon Cable Wrap for 13-15 Ft. Combination Assemblies PH 5-612 12 Ft. Black Nylon Cable Wrap for 15 Ft. Combination Assemblies • Easy to assemble and build custom 3-IN-1 combination assemblies • Easy to unwrap for cable repair/ replacement and DOT inspections • Uses hook-and-loop to securely fasten the wrap together • Simple and convenient alternative replacement for spiral wrap • Made from durable woven nylon for protection against the elements with double stitched ends to prevent fraying • Stainless steel grommets for cable ties for optional security • UV coated for sun protection and water resistant inner lining for winter weather protection Hook-and-Loop Fastener Stainless Steel Grommets Woven Nylon is UV Coated Double Stitched Ends Water Resistant Inner Lining CATALOG NUMBER 15 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15Phillips Air Line Inspection and Replacement Tech Tip TECH Tips CATALOG NUMBER 15 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ AIR LINE INSPECTION & REPLACEMENT In preparation for the winter months ahead, air lines should be inspected for damage to avoid air line failure on the road. However, component replacement is not only for the winter months, it can apply all year round. Although not always necessary, it’s a good practice to replace air lines, and air line accessories, annually to ensure proper working order. However, during routine PMs, or during pre-trip inspections, if any of the following are noted, air lines should be replaced much sooner to avoid possible air line failures, leading to downtime, or CSA violations. • Chaffing or damaged jacketing • Rusted springs and/or fittings • Nylon cables that are stretched out and no longer recoil • Kinked nylon cables When selecting airlines for a tractor/trailer most know that it is recommended, and in some cases even required by law, to choose air lines with the following features: • Air line assemblies that display the appropriate markings which signify compliance with DOT regulations (Required by law) • Swivel fittings on the tractor end to avoid corkscrewing during installation • Spring guards; to protect the hose or tubing from a sharp bend at or near the fitting (Required by law) • Added handle grips at the trailer end to provide protection from kinking of air lines during gladhand connection and disconnection • Coiled assemblies that extend to their maximum expected service length and return to their retracted position without sag • Proper overall working length for the tractor-trailer application • If operating in harsh environments, use cables rated for extreme temperatures [Lower than the typical standard of -40°F (-40°C)] When installing new air lines its always important to remember the following: • If cables or handles are color coded, be sure to install/couple them with their correlating connections (red to red, blue to blue). • Always remove the old fitting from the tractor protection valve and install the new fitting attached to the new air lines. Damaged Jacketing, Rusted Springs • Air lines should be inspected regularly. It is suggested to replace them annually or upon discovery of damage to the air lines. • If cables or handles are color coded, be sure to install/couple them with their correlating connections (red to red, blue to blue). • Always remove the old fitting from the tractor protection valve and install the new fitting attached to the new air lines. TIPS Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15Grote Assortment Fuse Kit Low Profile MINI ® , MINI ® /ATM, & ATO ® /ATC ® FEATURES & BENEFITS Cost-effective standard automotive fuse for use in automotive, battery & general DC applications TECHNICAL SPECIFICATIONS Material: Nylon PA 66 Voltage Amp: (5A, 10A, 15A, 20A, 25A, 30A), 32VDC Design Current Load: 1000A @ 32 VDC Pack Quantity: 180 Fuse Assortment Kit P/N GR182-ASST-180 MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 TRUCK PARTS SUPER STORE TM KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 JOPLIN 2424 Stephens Blvd. main 417.717.6022 fax 417.782.7126 parts 866.318.9111 October 1, 2018 (15Grote Assortment Fuse Kit) CATALOG NUMBER 15 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15QTT Corrosion Prevention CATALOG NUMBER 15 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ TECH Tips Plug Preventive Maintenance to Reduce Corrosion Build Up With the winter months coming soon it’s important to take extra precautions to keep your electrical system running smooth. Many states have increased the usage of Magnesium and Calcium Chlorides as a road de-icier. These chemicals are found to be highly corrosive to brass and copper, which is the base material for the contact pins used in plugs. To keep your products in top condition and to slow the process of corrosion, Phillips recommends the following maintenance tips. Apply dielectric grease to every plug and socket. This will keep moisture out and increase the flow of energy through the connection. Swap plug ends every 6 months to even out plug pin degradation. It is recommended that the 7-way plug interface be cleaned and greased at every preventive maintenance interval. Phillips interval suggestion is 3 months or more often if the vehicle is excessively exposed to magnesium or calcium chloride. • Use dielectric grease on every plug • Change plug ends routinely to even out pin degradation • Clean and grease 7-way plug and socket at every PM interval • Wash electrical cables, plugs and sockets more frequently in winter but never with power wash TIPS Wash electrical cables, plugs and sockets more frequently in winter weather with water. Do not power wash as water can be forced into areas and cannot escape, leading to corrosion. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15Tectran TEC360 Clamps CATALOG NUMBER 15 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ 3-HOLE TEC-360 ™ CLAMP Another Industry First! Tectran revolutionized the standard 3-hole clamp for tractor-trailer connection lines with the patented TEC-Clamp ™ and now has set the bar even higher with the new 3-Hole TEC-360 ™ Clamp (US Pat. D795052). It can be installed and adjusted without any hardware or tools needed and the TEC-360 ™ swivel top allows for the connection system to rotate and move freely during use in order to prevent: • Binding & tangling • Interlocked tender kit springs • Stress on connection points Red “power tab” (included) can be added to clamp so it can accept smaller OD, non-ABS 7-way cables Stainless steel Speed Clip for use with both Tender Kit & Pogo Stick suspension set-ups Swivel feature allows for full 360° rotation in either direction – no binding! Heavy duty polymer body with integrated hinge provides superior strength and high performance in the most extreme application environments Innovative and highly- secure aluminum locking clasp can be opened and closed by hand for installation and adjustment – No tools needed! 3-HOLE TEC-360 TM CLAMP PRODUC T BUL L E T I N Another Industry First! Tectran revolutionized the standard 3-hole clamp for tractor-trailer connection lines with the patented TEC-Clamp™ and now has set the bar even higher with the new 3-Hole TEC-360™ Clamp (US Pat. D795052) . It can be installed and adjusted without any hardware or tools needed and the TEC-360™ swivel top allows for the connection system to rotate and move freely during use in order to prevent: • Binding & tangling • Interlocked tender kit springs • Stress on connection points Stainless steel Speed Clip for use with b th Tender Kit & Pogo Stick suspension set-ups Swivel feature allows for full 360° rotation in either direction – no binding! Heavy duty polymer body with integrated hinge provides superio strength and high performance in the most extreme application environments Innovative and highly-secure aluminum locking clasp can be opened and closed by hand for installation and adjustment – No tools needed! Part No. 9888ST360 Stk. Code 47367 TECTRAN - USA TECTRAN - CANADA ™ US Pat. D795052 CLAMP. LOCK. GO. 3-HOLE TEC-360 TM CLAMP PRODUC T BUL L E T I N Another Industry First! Tectran revolutionized the standard 3-hole clamp for tractor-trailer connection lines with the patent TEC-Clamp™ and now h s set the bar even higher with the n w 3-Hole TEC-360™ Clamp (US Pat. D795052) . It can be installed and adjusted without any ardwar or tools needed and the TEC-360™ swivel top allows for the connection syste to rotate and move freely during use in order to prevent: • Binding & tangling • Interlocked tender kit springs • Stress on connection points Stainless steel Speed Clip f use with both Tender Kit & P Stick suspension set-ups Swivel feature allows for full 360° rotation in either direction – no binding! Heavy duty polymer body wi integrated hinge provides su stre gt and high performan in the ost extreme applica environments Innovative and highly-secure aluminum locking clasp can opened and closed by hand installation and adjustment – No tools needed! Part N o. 9888ST360 Stk. Code 47367 ™ US Pat. D795052 CLAMP. LOCK. GO. 3-HOLE TEC-360 TM CLAMP PRODU T BUL L E T I N Anoth r I ustry First! Tectran revolutionized the standard 3-hole clamp for tractor-trailer connection lines with the patented TEC-Clamp™ and now has set the bar even higher with the new 3-Hole TEC-360™ Clamp (US Pat. D795052) . It can be installed and adjusted without any hardware or tools needed and the TEC-360™ swivel top allows for the connection system to rotate and move freely during use in order to prevent: • Binding & tangling • Interlocked tender kit springs • Stress on connection points Stainless steel Speed Clip for use with both Tender Kit & Pogo Stick suspension set-ups Swivel feature allows for full 360° rotation in either direction – no binding! Heavy duty polymer body with integrated hinge provides superior strength and high performance in the most extreme application environments Innovative and highly-secure aluminum locki g clasp can be opened and closed by hand for installation and adjustment – No tools needed! Part No. 9888ST360 Stk. Code 47367 TECTRAN - USA 2345 Walden Ave., Suite 100 Cheektowaga, NY 14225 TECTRAN - CANADA 2400 Anson Drive Mississauga, ON L5S 1G2 www.tectran.com ™ US Pat. D795052 CLAMP. LOCK. GO. Compatible with both coiled and straight connection lines for maximum application coverage P/ TC 9 88ST360 CLAMP. LOCK. GO Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

38Automann Air Spring Rolling Lobe Freightliner CATALOG NUMBER 38 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ NEW! ECONORIDE AIR SPRING ROLLING LOBE AUT566.ER9781-24 Fits Freightliner Rear FAS Airliner II Suspension MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 TRUCK PARTS SUPER STORE TM KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 JOPLIN 2424 Stephens Blvd. main 417.717.6022 fax 417.782.7126 parts 866.318.9111 Cross Reference Alliance ABP N32 019781 Hendrickson Truck 8536 Firestone 9781 Firestone W01-358-9781 Firestone W01-377-8536 Firestone W013589781 Firestone W013778536 November 9, 2021 (38Automann Air Spring Rolling Lobe Freightliner) OE Cross Reference 16-16730-000 16-13810-000 16-13810-002 16-13840-000 16-14004-000 16-14377-000 16-16773-000 16-19466-000 A16-13688-002 A16-14004-001 A16-17574-001 A16-17574-002 A16-18335-000 A16-18335-001 Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

06Kit Masters PolyForce Belt Tensioners K5 689448 OEM # 38610, 49582, 89448, 3104149, 3682683, D1186-2633, 38567, 3690067 K5 689440 Mfg. # Peterbilt: 3682946 Kenworth: 3682946 Mack: 3682946 Cross Ref. # 89440, 49563 K5 689477 Mfg. # Volvo: 21568413, 21454379 Cross Ref. # 89477, 49601 K5 689419 Mfg. # Freightliner: 01-27245-000 Cross Ref. # 89419 No Springs Attached Conventional belt tensioners use springs to hold their position and tension. However, springs can only flex so many times before they fail. PolyForce Belt Tensioners replace this spring with a New and unique Polymer Torsion Core A longer lasting compressed polymer replaces the spring, thereby eliminating the primary cause of failure. The Polymer Torsion Core also doubles as a built-in damper, reducing stress on adjacent accessories without additional damage to the belt tensioner. TENSIONERS REINVENTED! P/N K5 638667 Replaces OEM #s: 38667, 49603, 89498, 89498A, A4-72200-0170, A4-72200-0270 , A4-72200-0470, A4-72200-0570 , A4-72200-0970 THE MOST POPULAR BELT TENSIONER ON 08-17 FREIGHTLINERS WITH DD13, DD15 & DD16 ENGINES Improved Bearings Pulley bearing absorbs a huge amount of vibration and can often fail too soon. To extend bearing life, PolyForce tensioners feature heavy-duty bearing that have a 40% higher load rating than the OEM and feature Anti-Vibration Grease, which won’t separate. Standard PolyForce PULLEY PolyForce pivot bushings OEM pivot bushings Misaligned Alignment - Wider is Better Misaligned belt tensioners lead to damaged tensioners, belts & accessories. A worn pivot bushing is typically the culprit of misalignment. PolyForce pivot bushings have a much wider stance, giving them drastically increased stability. 2 Year / 200,000 Mile WARRANTY CATALOG NUMBER 06 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Long-Term Savings • Long-lasting components • Reduced belt & accessory wear • Replace individual tensioners instead of entire unit Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

29Grote DOT Solution 60711 The “DOT” Solution 49322 49412 49413 49333 60661 60651 60721 LED Clearance / Marker Lamps LED License Lamps • Brackets & Grommets GR 49362 - Red w/ Grommet, Slim-Line GR 49363 - Yellow w/ Grommet, Slim-Line • Dual Intensity allows for better visibility • Hermetic lens-to-housing seal • Encapsulant potting for total circuit board protection against vibration and corrosion • Sleek aerodynamic styling, small size fits in narrow applications Dual Intensity MicroNova ® Dot LED Clearance / Marker Lamp MicroNova ® Dot LED Clearance / Marker Lamp GR 60661 - Gray, Lamp with Adaptor Bracket GR 60651 - Replacement Lamp GR 60721 - Lamp with Hooded Grommet GR 60711 - KIT: Gray (60661+43780 Mounting Bracket) • Durable one-piece LED lamp design • Hardwired with .180 slim-line UBS plug connections for maximum performance • Indexed, snap-fit mounting to brackets • Direct replacement to existing 60291 (Incandescent) offering MicroNova ® Dot LED License Lamp GR 49322 - Red, w/ Grommet GR 49332 - PC RATED: Red, w/ Grommet GR 49333 - PC RATED: Yellow P2/PC w/ Grommet GR 49412 - Red, w/ Adaptor Bracket GR 49413 - Yellow, w/ Adaptor Bracket • Available in PC and P2 versions • Sleek aerodynamic styling extends less than 3/8” from mounted surface • No fasteners required • Available in 12V and 24V versions CATALOG NUMBER 29 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

29Ecco ED3040 ED3060 Directional LEDs P/N LED COLOR EC ED3794AW Amber/White EC ED3794BA Blue/Amber EC ED3794BW Blue/White EC ED3794RA Red/Amber EC ED3794RB Red/Blue EC ED3794RW Red/White CATALOG NUMBER 29 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ P/N SHAPE CONNECTOR LENS EC ED3040AW Round PL3 Clear Center: Reverse/Warning Red Perimeter: Stop-Turn-Tail EC ED3060AW Oval PL3 Clear Center: Reverse/Warning Red Perimeter: Stop-Turn-Tail DIRECTIONAL LEDS Stop-Tail-Turn-Reverse and Warning Light Combo DIRECTIONAL LEDS ED3794 UltraFlex ™ Dual-Color Flexible LED Light These low-profile, multifunctional lights maximize visibility on the back of the vehicle. Use them to indicate stop-turn-tail-reverse with steady burn red and white colors. When warning lights are activated, the dual-color lights provide 69 attention-grabbing flash patterns. ECCO’s UltraFlex is a versatile directional warning light that can be mounted on flat or curved surfaces up to 120° with self-adhesive, very high bond tape. Its 12 dualcolor LEDs provide exceptional output with combinations of amber, white, blue and red colors available. The light heads are protected in a clear, silicone housing that can flex while resisting yellowing and warping. A two-bolt bezel is also included for easy installation on flat surfaces. • 12-24 VDC • 69 flash patterns • High output LEDs offer low maintenance, long life and low current consumption • Ultrasonically sealed housing • Grommet mount included to fit in standard 4” rounded or 6” oval tail light applications • Flange mount available with optional accessories • Vibration and shock resistant construction • Connector for Ground, Stop/Turn, Tail • Temperature Range: -22°F to +122°F (-30°C to +50°C) • 12-24 VDC, 0.8 AMPS • 69 flash patterns including steady burn • Flexible housing adapts to curved surfaces up to 120° (product cannot be bent in forward position) • Silicone lens with Dow Corning material, prevents yellowing or aging • Included bezel for two-bolt mount on flat surfaces or VHB tape mount • Sync-capable • Temperature range: -22°F to 122°F (-30°C to 50°C) ACCESSORIES EC EZ3040FLG Flange for ED3040AW EC EZ3060FLG Flange for ED3060AW 5.4" 4.0" 6.5" 3.3" 7.5" NEW! NEW! Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15Grote Deutsch Terminal and Connector Assortment Kit Barrel Crimper GR184-9449 • Used for open barrel OEM Packard style connectors • Can crimp non-insulated terminals 22 - 10 Gauge • Heavy duty construction • Ergonomic design 10” • Used for open barrel contacts only DEUTSCH TERMINAL & CONNECTOR ASSORTMENT KIT GR183-6549 Crimpers • Handy new 18 compartment Deutsch Kit includes 98 assorted DT Series connectors, thermoplastic housings and wedge locks • Kit includes an easy to use reorder reference chart on the inside cover • Sturdy plastic re-closable container keeps all the connectors in one convenient location • Terminals are rated at 13 amps @ 125°C (257°F) continuous operating temperature • Silicon seals included with the housings provide a superior seal • Deutsch DT series environmentally sealed connectors are designed specifically for cable to cable applications Two Indent Crimp GR183-6517 • Compact and easy to use side measuring dial • No need to change out dies and locators • Crimps all wire ranges of contact sizes • Used for solid barrel contacts only NEW! DEUTSCH TERMINAL & CONNECTOR SERVICE KIT GR183-6568 CATALOG NUMBER 15 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ CRIMPING TOOLS – DEUTSCH PART # WIRE GAUGE TERMINAL STYLE GR183-6562 14, 16, 18 Solid Barrel GR183-6563 20, 22 Solid Barrel GR183-6564 14, 16, 18, 20, 24 Open Barrel (Deutsch + Weather Pack) REMOVAL TOOL KIT – DEUTSCH GR183-6567 14, 16, 18, 20, 24 Solid & Open Barrel; Gold, Blue, Red Handles INCLUDES: • Ideal for any repair shop or installer of Deutsch terminals & connectors • 6 piece tool kit to for crimping/releasing both solid & open barrel Deutsch terminals • Includes 3 crimping tools for open and closed barrel terminals and 3 terminal release tools • Supplied in a durable plastic molded storage case for easy storage and application Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

29GoLight Lights Exclusive CR5 Pentabeam Technology 370° Rotation x 135° Tilt 225,000 Candela, Max Beam Distance 3,113 ft 5.5 amps at 13.8V GOLIGHT / RADIORAY HALOGEN REMOTE CONTROL SEARCHLIGHTS Wireless • Remote Controlled • Portable RADIORAY Halogen P/N G2 7901 (White) Package Includes: • Wireless Handheld Remote • Magnetic Mount Shoe & Suction Cup • 15’ Power Cord with Cigarette Plug RADIORAY Halogen P/N G2 7900 (White) Package Includes: • Wireless Handheld Remote • Permanent Mount Shoe & Suction Cup • 15’ Power Cord with Cigarette Plug 8° Beam Angle 65 watt H9 Bulb UV Ray and Saltwater Resistant 3 Year Limited Warranty CATALOG NUMBER 29 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

29Ecco Snow Plow Lights and Light Bars CATALOG NUMBER 29 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ EW4010 SERIES Heated LED Snowplow Worklamp EW4009 SERIES Low Profile Heated LED DOT Worklight EW4008 SERIES LED DOT Worklight ▪ High Beam / Low Beam / Position Light / Indicator ▪ Snow-melt and anti-icing system (patented technology) ▪ DOT certified ▪ Dual options for bottom and back mounting ▪ Multi-directional mounting for signal light (left/right/top) ▪ Unique aluminum heatsink housing design for maximum heat management ▪ Black powder-coated, diecast aluminum alloy housing and heat sink ▪ Tempered glass lens with polycarbonate reflector optics ▪ 6.7” H x 5.9” W x 3.3” D, 6.7” H x 9.0” W x 3.3” D (with parking light) ▪ Estimated lens temperature when the heat function is turned on, with a 5mm layer of ice on lens with vehicle working in a -13°F (-25°C) environment 1 minute: 0°F (-18°C) | 5 minutes: 30°F (-1°C) | 10 minutes: 59°F (15°C) | 1 hour: 154°F (68°C) – the maximum temperature the light will reach) ▪ IP68 waterproof breather and a 5-year warranty ▪ Packaged in pairs ▪ High Beam / Low Beam / Indicator / Marker ▪ Snow-melt and anti-icing system ▪ Unique aluminum heatsink housing design for maximum heat management ▪ Black powder-coated, diecast aluminum alloy housing and heat sink ▪ UV stabilized polycarbonate lens and reflector optics ▪ Low Beam: Two 16.6-Watt LEDs ▪ Marker Light: Twelve .55-Watt LEDs ▪ Indicator: Twelve 6.8-Watt LEDs ▪ Packaged in pairs ▪ Unique aluminum heatsink housing design for maximum heat management ▪ Black powder-coated, diecast aluminum alloy housing and heat sink ▪ UV stabilized polycarbonate lens and reflector optics ▪ Low Beam: Two 12-Watt LEDs ▪ Marker Light: Eight 3-Watt LEDs ▪ Indicator: Eight 3-Watt LEDs EW4010 Includes a pair of worklamps Accessories (Not Included) EC EZ4010-LIGHT - Universal Lighthead w/o harness EC EZ4010-WIRE - 10’ Replacement wire harness EC EZ4010-MK - Replacement mounting kit EC EW4010 V OLTAGE 12-24 LUMENS (RAW) 1800 (low beam), 3600 (high beam) AMPS 1.6 (low beam), 3.2 (high beam) EC EW4009 V OLTAGE 12-24 LUMENS (RAW) 1000 (low beam), 1700 (high beam) AMPS 1.4 (low beam), 3.5 (high beam) EC EW4008 V OLTAGE 12-24 LUMENS (RAW) 1600 (low beam), 2400 (high beam) AMPS 1.7 (low beam), 2.7 (high beam) LOW PROFILE DEPTH 1.8" | HEIGHT 2.7" The EW4009 Series worklight offers the latest technology and the very brightest white light for your application. Designed for headlight replacement, as well as vehicles working in inclement weather, this LED model features a heated lens to melt away snow and ice and offers over 80,000 hours of maintenance-free life expectancy coupled with low amp draw. High-intensity light output and CE rating makes this the ideal choice for a wide variety of DOT applications. Additional features include 12-24 VDC operation, shock-resistant mounting, IP67 waterproof breather and a 5 year warranty. The EW4008 Series worklight offers the latest technology and the very brightest white light for your application. Designed for headlight replacement, as well as vehicles working in inclement weather, this LED model offers over 60,000 hours of maintenance-free life expectancy coupled with low amp draw. High-intensity light output and CE rating makes this the ideal choice for a wide variety of DOT applications. Additional features include 12-24 VDC operation, shock-resistant mounting, IP67 waterproof breather and a 5 year warranty. HEATED! HEATED! Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

39Equal Tire Performance New FLEXX Upgrade to the latest in technology with Equal FLEXX With 2X more vibration absorption power, EQUAL FLEXX is the new industry benchmark in wheel- end balancing, delivering more even tire wear, lower rolling resistance and the smoothest ride. EQUAL FLEXX Drop In Bag IM EQFXWC32 Case of (32) W pkgs. (16 oz.) IM EQFXAC40 Case of (40) A pkgs. (12 oz.) IM EQFXBC40 Case of (40) B pkgs. (10 oz.) IM EQFXCC40 Case of (40) C pkgs. (8 oz.) IM EQFXDC40 Case of (40) D pkgs. (6 oz.) IM EQFXEC40 Case of (40) E pkgs. (4 oz.) IM EQFXFC40 Case of (40) F pkgs. (3 oz.) • No filtered valve core required means simpler installation • Drop in Bag application with simplified quantity chart • Larger particle size makes it easier to remove • No slip hazard on the shop floor • More fuel savings, more even tire wear, and the smoothest ride • 2x more vibration absorption power • 15% better performance • Easier to use WHY BALANCE YO UR WHEE L-ENDS? Balancing all wheel p ositions has been proven to improve fuel economy up to 2% reducing rolling resistance for the life of the tires. The savings multiply because fuel efficiency increases as the tread wears down. In fact, the last 1/5 of a tire’s uses 6.5% less fuel than new tread. Yet most tires have to be replaced prematu to uneven wear, taking them out of service just as fuel economy peaks. Unbalanced tires also reduce tire life. More even wear yields maximum tread life extend the takeoff mileage. Balanced tires last up to 40% longer than unbalance saving money on equipment costs while reducing maintenance expenses. E QUAL w orks continuously to balance tires and the rest of the wheel assembly, which dampens vibrations for bushings, U-joints, lights, batteries and the overall suspension. Less wear-and-tear on the truck means lower overall maintenance costs for the life of the vehicle. A smoother ride also reduces dr iver fatigue and a comfortable driver is more likely to stay with your fleet. Fleet managers are charged with decreasing cost per mile. Every tire-related issu your fleet faces results in time spent in maintenance and repair rather than on th Each tick of the clock drives CPM higher. These costs add up quickly both in replacement equipment and in lost time. TIRE WEAR FUEL COST The results? The EQUAL family minimizes tire wear for a lifetime of use, and maximizes your fleet’s productivity and profitability. SMOOTHER RIDE PRODUCTIVITY mentality I w plainly delive it came to ex reducing cos -VP of Maint WHY BALANCE YO UR WHEE L-ENDS? Balancing all wheel p ositions has been proven to improve fuel economy up to 2% reducing r olling resis tance for the life of the tires. The savings multiply because fuel efficiency increases as the tread wears down. In fact, the last 1/5 of a tire’s uses 6.5% less fuel than new tread. Yet most tires have to be replaced prematu to uneven wear, taking them out of service just as fuel economy peaks. Unbalanced tires also reduce tire life. More even wear yields maximum tread life extend the takeoff mileage. Balanced tires last up to 40% longer than unbalance saving money on equipment costs while reducing maintenance expenses. EQUAL works continuously to balance tires and the rest of the wheel assembly, w hich da mpens vibrations for bushings, U-joints, lights, batteries and the overall s uspens i n. Less wear-and-tear on the truck means lower overall maintenance costs for the life of the vehicle. A smoother ride also reduces driver fatigue and a comfortable driver is more likely to stay with your fleet. Fleet managers are charged with decreasing cost per mile. Every tire-related issu your fleet faces results in time spent in maintenance and repair rather than on th Each tick of the clock driv s CPM higher. These costs add up quickly both in replacement equipment and in lost time. TIRE WEAR FUEL COST maximizes your fleet’s productivity and profitability. SMOOTHER RIDE PRODUCTIVITY it came to ex reducing cos -VP of Maint WHY BALANCE YOUR WHEEL-ENDS? Balancing all wheel positions has been proven to improve fuel economy u re ducing rolling re sistance for the life of the tires. The savings multiply b fuel efficiency increases as the tread wears down. In fact, the last 1/5 o uses 6.5% less fuel than new tread. Yet most tires have to be replaced p to uneven wear, taking them out of service just as fuel economy peaks. Unbalanced tires also reduce tire life. More even wear yields maximum t extend the takeoff mileage. Balanced tires last up to 40% longer than un saving money on equipment costs while reducing maintenance expenses EQUAL work c tinuously to b lance tires and he rest f the wheel as which dampe s vibrations for bushings, U-joints, lights, batteries and he suspension. Less wear-and-tear on the truck me ns lower overall mainte costs for the life of the vehicle. A smoother ride also reduces driver fatig a comfortable driver is more likely to stay with your fleet. Fleet managers are charged with decreasing cost per mile. Every tire-rela your fleet faces results in time spent in maintenance and repair rather th Each tick of the clock drives CPM higher. These costs add up quickly bot replacement equipment and in lost time. TIRE WEAR FUEL COST SMOOTHER RIDE PRODUCTIVITY WHY BALANCE YOUR WHEEL-ENDS? Balancing all wheel positions has been proven to improve fuel economy u reducing rolling resistance for the life of the tires. The savings multiply b fuel efficiency increases as the tread wears down. In fact, th last 1/5 o us es 6.5% ess fu el han new read. Yet most tires ave to be rep aced p to uneven wear, taking them out of service just as fuel economy peaks. Unbalanced tires also reduce tire life. More even wear yields maximum t extend the takeoff mileage. Balanced tires last up to 40% longer than un saving money on equipment costs while reducing m intenance e penses EQUAL wo rk co tinuously to balance tires and the rest f the wheel ass which dam pens vibrations for bushings, U-joints, lights, batteries and the suspensi n. Less we r-an -tear o the truck m ans lower ov rall ma nte co ts for th life of th vehicle. A moother ride also reduces river f ig a comfortable driver is more likely to stay with your fleet. Fleet managers are charged with decreasing cost per mile. Every tire-rela your fleet faces results in time spent in maintenance and repair rather th Each tick of the clock d iv s CPM high r. These costs add up quickly bot replac ment quipment and in lost time. TIRE WEAR FUEL COST SMOOTHER RIDE PRODUCTIVITY P/N Description IM FVC-1 AirX Filtered Valve Core HL DS-1 Flow-thru Cap IM EQ-VSF-EXT-NP Nickle Valve Stem Filter Extension MAXIMIZE YOUR EXPERIENCE. �� �ro� the F����� EDJ into the tire before �ountin�� �o not tear or o�en� �� P lace FLEXX valve core into tire ste� F RU D OLPLWHG WLPH H ve ry F���� �urchase ZLOO include a �ltered valve core and ���� �o��thr X ca� to be used as �art of your F���� installation to add value and t thank you for your continued business! HOW TO INSTALL: �� Place FLEXX identification sleeve over valve stem. 4 � Lastly, hand-tighten flow- through cap. ZLWK LQIODWLQJ DGMXVWLQJ DQG JDXJLQJ \RXU WLUH SUHVVXUH $70 Val e MAXIMIZE YOUR EXPERIENCE. �� ro� the F����� EDJ into the tire before untin�� �o not tear or o�en� �� P lace FLEXX valve core into tire ste� F RU D OLPLW G WLP H H very F���� �urchase ZLOO include a �ltered valve core and � � �o��thr X ca� to be used as �art of your F���� installation to add value and to thank you for your contin ed business! HOW TO INSTALL: �� Plac FLEXX identification slee over valve stem. 4 � Lastly, hand-tighten flow- through cap. ZLWK LQIODWLQJ D MXVWLQJ DQG JDXJLQJ \R WLUH SUHVVXUH $70 Value MAXIMIZE YOUR EXPERIENCE. �� �ro the F����� EDJ into th ti before �ounti �� �o not tear or o�en� �� P lace FLEXX valve core into tire ste� F RU D OLPLWH G WLPH H very F� �� �urchase ZLOO include a �ltered valve core and ��� �o��thr X ca� to b used s �art of your F���� ins lla ion to add value and to thank you for your co tinued bus ness! HOW TO INSTALL: �� Place FLEXX identification sl eve over valve stem. 4 � L stly, hand-tighten flow- through cap. ZLWK LQIODWLQJ DGMXVWLQJ DQG JDXJLQJ \RXU WLUH SUHVVXUH $70 Value MAXIMIZE YOUR EXPERIENCE. �� �ro� the F����� DJ into th ti before �ountin�� �o not tear or o�en� �� P lace FLEXX valve cor in o tire ste� F RU D OLP LWHG WLPH H very F� �� �urchase ZLOO includ a � tered valv core and ���� �o��thr X ca� to be used as �art of your F���� ins alla ion to add value d to thank you f r yo r con inued business! H W TO INSTALL: �� Place FLEXX identification sl e e over valve stem. 4 � Lastly, hand-tighten flow- through cap. Z WK LQIO WLQJ GMXVWLQJ DQG JD JLQJ \RXU WLUH SUHVVXUH $70 V l e Drop the FLEXX ™ bag into the tire before mounting. Do not tear or open Place FLEXX valve core in tire stem. Place FLEXX identifi ation sleeve over valve stem. L stly, hand-tighten flow-thru cap ACCESSORIES AIR-LOCK TIRE LUBE & BEAD SEAL IS ALCS4128 1 gallon HOW TO INSTALL: INCLUDED! Every FLEXX purchase will include a filtered valve core and for a limited time HL DS-1 flow-thr cap (indicated with red “new hardware” sticker on the box) to be used as part of your FLEXX installation to add value and to thank you for your continued business! CATALOG NUMBER 39 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 39Equal Tire Performance New FLEXX MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 TRUCK PARTS SUPER STORE TM KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 JOPLIN 2424 Stephens Blvd. main 417.717.6022 fax 417.782.7126 parts 866.318.9111 October 26, 2017 (39Equal Tire Performance New FLEXX) EQUAL FLEXX WHEEL-END SOLUTION Fleet Minded Dual Force Active Balancing Technology We put 50+ compounds to the test as we developed EQUAL FLEXX – the newest member of the EQUAL family – and determined it wasn’t one compound that maximizes vibration reduction, but a combination of two compounds that react and absorb force better than any other internal wheel-end balancer on the market. The results? Like its predecessor, EQUAL FLEXX dampens vibration by adapting to the wheel and brake assembly, and its Dual Force active balancing compounds reduce total tire vibration. Rigorously Tested, Scientifically Refined, Fleet Validated IMI drew upon our unprecedented expertise over the past 25 years with EQUAL in the development of EQUAL FLEXX. We partnered with the foremost experts in vibration analysis and tire testing. Final validations were performed over the road, having hundreds of thousands of recent miles of truck data to draw upon. Tests have shown up to 15% better performance. Using an onboard wireless vibration sensing system, the controlled testing process gave engineers a first- hand look at what happens inside a tire in real time, producing empirical data that led to the exact compounds in EQUAL FLEXX. With 2X more vibration absorption power, EQUAL FLEXX is the new industry benchmark in wheel-end balancing, delivering more even tire wear, lower rolling resistance and the smoothest ride. SAND GLASS EQUAL EQUAL FLEXX THE SOFTNESS SCALE EQUAL FLEXX will never damage the tire casing, wheel or TPMS units. It does not void tire manufacturer warranties. As the softest internal balancing compound available, EQUAL FLEXX maximizes vibration dampening for the life of a tire. WHY DOES VIBRATION MATTER? Simply put, vibration is wasted energy, and wasted energy increases rolling resistance. EQUAL FLEXX absorbs this energy and the accompanying vibrations within the tire, reducing tire wear, lowering fuel cost by lessening rolling resistance, and delivering a smoother ride. Energy absorption happens everywhere on the tire’s circumference where vibration occurs, not just at the footprint. In turn, vibrations are decreased through the complete tire and wheel assembly. * Patent Pending NEW! Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15Grote Cable Ties  NOW AVAILABLE! THE ISSUE WITH LOW HUMIDITY Relatively low humidity including storage in an uncontrolled environment can cause cable ties to dry out and can cause premature breakage and installation issues. Introducing our NEW Elite Cable Ties designed to deal with the harshest conditions. The newly modified reinforced Nylon 6/6 raw material absorbs and releases moisture as the atmosphere changes, especially in winter months when conditions are cold with little humidity. GROTE HAS A SOLUTION FOR YOU! NEW LOCKING DESIGN Grote’s new and improved cable tie includes a new locking design engineered to achieve 25% more tensile strength than advertised. In addition, added moisture during manufacturing helps to protect the ties from environmental factors like low humidity and Ultra Violet Rays (U.V.). DID YOU KNOW? Be secure with Cable Ties that stay strong in ALL climates and weather conditions HYGROSCOPIC CABLE TIES 6 6 MORE TENSILE STRENGTH 25 % FEATURES & BENEFITS Made in USA Virgin Nylon 6/6 RawMaterial UL 62275 Type 2, 21 & 21S UV Black Rated Mil-Spec Approved Performance Series Competitive Pricing Cold Weather line Ship From Stock NEW LOCKING DESIGN Grote’s new and improved cable tie includes a new locking design engineered to achieve 25% more tensile strength than advertised. In addition, added moisture during manufacturing helps to protect the ties from environmental factors like low humidity and Ultra Violet Rays (U.V.). FEATUR S BENEFITS • Made in USA • Virgin Nylon 6/6 Raw Material • UL 62275 Type 2, 21 & 21S • UV Black Rated • Mil-Spec Approved • Performance Series • Competitive Pricing • Cold Weather line CATALOG NUMBER 15 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ HYGROSCOPIC CABLE TIES Be secure with Cable Ties that stay strong in ALL climates and weather conditions Nylon cable ties are hygroscopic – this means they absorb and release water as the atmosphere changes, especially in winter months when conditions may be not only cold but also dry. Virtually all brittleness problems occur in this type of weather or where cable ties have been stored in an uncontrolled condition. A moisture content of 2.5% allows for flexibility and easy bending of the straps. When moisture in the produc is below 1%, they can become brittle. FOR MORE INFORMATION VISIT OUR WEBSITE AT GROTE.COM GROTE’S GOT IT! C O N N E C T & P R O T E C T THE BENEFITS OF TIES MADE FROM NYLON 6/6 RAWMATERIAL • They will absorb and release moisture as the atmosphere changes • During manufacturing we add up to 2.5% moisture to the packaging • It takes 48 hours for the moisture to be absorbed into the Nylon 6/6 • Moisture is what gives cable ties their flexibility • In dry conditions moisture will release from Nylon 6/6 within 24 hours Nylon cable ties and duct straps are hygroscopic – this means they absorb and release water as the atmosphere changes, especially in winter months when conditions may be not only cold but also dry. Virtually all brittleness problems occur in this type of weather or where cable ties have been stored in an uncontrolled condition. A moisture content of 2.5% allows for flexibility and easy bending of the straps. When moisture in the product is below 1%, they can become brittle. The pawl (l ck) inside the head of the straps must flex (“see-saw”) over the teeth of the strap. When the humidity is below 40%, mostly in winter months, the pawl may not flex and can be forced to pop out upon insertion of the strap into the head. The strap of the tie may also become brittle and crack under these conditions.  NOW AVAILABLE! 230 Travail Rd, Markham, Ontario, Canada L3S 3J1 Tel: 800.268.5612 US: 800.628.0809 www.grote.com RoHS 62275-TYPE 2, 21 & 21S DID YOU KNOW? HYGROSCOPIC CABLE TIES HOW TO SELECT THE RIGHT CABLE TIE STEP 1 | SELECT THE RIGHT CABLE TIE MATERIAL FOR THE JOB • Standard Nylon 6/6 – for everyday indoor/outdoor bundling applications • Elite cold weather – for dry, cold climate where humidity is low STEP 2 | SELECT THE RIGHT TENSILE STRENGTH & LENGTH FOR THE JOB • 18lb up to 175lb • Choose the cable tie length for the desired bundle diameter needed – 4" to 36" lengths STEP 3 | PROPER INSTALLATION RECOMMENDATIONS • UL tests and recommends installation temperatures at or greater tha 32° F (0°C) & 40% humidity • Over-tightening of the strap can cause failure • When installing cable ties, make sure a proper tensioning tool is used to ensure the correct force is applied STEP 4 | PROPER STORAGE RECOMMENDATIONS • Ties should be stored in a sealed bag in a heated area. • UL recommends storage of Nylon 6/6 straps at 70°F (21°C) a d 50% humidity HYGROSCOPIC A property of a substance that absorbs and releases moisture from the air of its surroundings R E L AT I V E H U M I D I T Y % 40 NYLON 6/6 RELEASES MOISTURE NYLON 6/6 ABSORBS MOISTURE Be secure with Cable Ties that stay strong in ALL climates and weather conditions THE ISSUE WITH LOW HUMIDITY Relatively low humidity including storage in an uncontrolled environment can cause cable ties to dry out and can cause premature breakage and installation issues. GROTE HAS A SOLUTION FOR YOU! Introducing our NEW Elite Cable Ties designed to deal with the harshest conditions. The newly modified reinforced Nylon 6/6 raw material absorbs and releases moisture as the atmosphere changes, especially in winter months when conditions are cold with little humidity. THE BENEFITS OF TIES MADE FROM NYLON 6/6 RAW MATERIAL • They will absorb and elease moisture as the atmosph re changes • During manufacturing we add up to 2.5% moisture to the packaging • It takes 48 hours for the moisture to be absorbed into the Nylon 6/6 • Moisture is what gives able ties their flexibility • In dry conditions mo sture will release from Nylon 6/6 within 24 hours Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 15Grote Cable Ties MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 TRUCK PARTS SUPER STORE TM KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 JOPLIN 2424 Stephens Blvd. main 417.717.6022 fax 417.782.7126 parts 866.318.9111 STANDARD TIE P/N Ref # Color Length Bundle Dia. Strength Qty. 1000 Pack Option* All Weather HD GR183-6000 TC 933-1 White 4.1" 0.75" 18 LB PK 100 83-6000-3 N/A GR183-6001 TC 933-1B Black 4.1" 0.75" 18 LB PK 100 83-6001-3 GR183-6001C GR183-6006 TC 933-2 White 5.8" 1.25" 40 LB PK 100 83-6006-3 N/A GR183-6007 TC 933-2B Black 5.8" 1.25" 40 LB PK 100 83-6007-3 GR183-6007C GR183-6020 TC 933-2L White 11.1" 3" 50 LB PK 100 83-6020-3 N/A GR183-6021 TC 933-2LB Black 11.1" 3" 50 LB PK 100 83-6021-3 GR183-6021C GR183-6018 TC 933-3 White 7.6" 2" 50 LB PK 100 83-6018-3 N/A GR183-6019 TC 933-3B Black 7.6" 2" 50 LB PK 100 83-6019-3 GR183-6019C GR183-6026 TC 933-4 White 14.6" 4" 50 LB PK 100 83-6026-3 N/A GR183-6025 TC 933-4B Black 14.6" 4" 50 LB PK 100 83-6025-3 GR183-6025C GR183-6028 TC 933-5, TC 933-6 White 15" 4" 120 LB PK 100 83-6028-3 N/A GR183-6029 TC 933-5B Black 15" 4" 120 LB PK 100 83-6029-3 GR183-6029C GR183-6118 TC 933-8 White 37.25" 11" 175 LB PK 50 N/A N/A COLORED STANDARD TIE GR185-6032 TC 933-3-02 Blue 8" 2" 50 LB PK 25 N/A N/A GR185-6034 TC 933-3-04 Green 8" 2" 50 LB PK 25 N/A N/A GR185-6030 TC 933-3-05 Red 8" 2" 50 LB PK 25 N/A N/A DUAL CLAMP TIE GR185-6040 TC 936-131 Black 13" 1.3" 150 LB PK 10 N/A N/A GR185-6041 TC 936-191 Black 19.2" 2.3" 150 LB PK 10 N/A N/A EDGE CLIP ASSEMBLY GR185-6063 - Black, Top Mount 7.9" 1.8" 50 LB PK 25 N/A N/A GR185-6064 - Black, Side Mount 7.9" 1.8" 50 LB PK 25 N/A N/A BUTTON HEAD TIE GR183-6049 - Black 9.6" 2.62" 105 LB PK 50 N/A N/A GR183-6052 - Black 15" 4.33" 130 LB PK 50 N/A N/A January 28, 2020 (15Grote Cable Ties) HYGROSCOPIC CABLE TIES Be secure with Cable Ties that stay strong in ALL climates and weather conditions *Contact your salesman if you are interested in the 1000 pack option Step 1: Select the right cable tie material for the job • Standard nylon 6/6 – for everyday indoor/outdoor bundling applications • Elite cold weather – for dry, cold climate where humidity is low Step 2: Select the right tensile strength & length for the job • 18lb to 175lb • Choose the cable tie length for the desired bundle diameter needed – 4" to 36" lengths Step 3: Proper installation recommendations • UL tests and recommends installation temperatures at or greater than 32° F (0°C) & 40% humidity • Over-tightening of the strap can cause failure Step 4: Proper storage recommendations • Ties should be stored in a sealed bag in a heated area • UL recommends storage of Nylon 6/6 straps at 70°F (21°C) and 50% humidity Tips & Recommendations for Selecting the Right Cable Tie TECH Tips Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

39AutoSock Tire Chain Alternative CATALOG NUMBER 39 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ AutoSock ® - the simple solution to maximize friction on snow and ice. And the secret: high-performance fibers! AutoSock ® for Trucks is a textile cover designed to help you out of a difficult situation. » A perfect temporary winter aid for trucks » Quick and easy to fit and remove » AutoSock for Truck approved as an alternative traction device to tire chains by Colorado Department of Transportation, Washington State Patrol, and the Department of California Highway Patrol » Proven to enhance trucks’ electronic safety systems » Easy to store and lightweight » Self-centering » Reusable » Patent-protected Tire sizes AutoSock ® 305/70 R19.5 6R AL71 $199.00 275/80 R20 825 R20 245/75 R22.5 255/70 R22.5 275/70 R22.5 295/60 R22.5 9.00 R22.5 255/80 R22.5 ASKAL74 $226.00 295/70 R22.5 315/60 R22.5 275/80 R22.5 6R AL79 $226.00 295/75 R22.5 315/70 R22.5 10.00 R22.5 285/75 R24.5 6R AL84 $226.00 295/80 R22.5 315/80 R22.5 11.00 R22.5 275/80 R24.5 12.00 R20 ASKAL89 $226.00 12.00 R22.5 11.00 R24.5 445/50 R22.5 ASKAL111 $226.00 Now covering Super Singles! Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 39AutoSock Tire Chain Alternative MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 TRUCK PARTS SUPER STORE TM KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 JOPLIN 2424 Stephens Blvd. main 417.717.6022 fax 417.782.7126 parts 866.318.9111 AutoSock the alternative to chains Light weight » Increases fuel mileage » Eliminates the need for chain hangers and reduces overall weight » AutoSock weighs approx 5 lbs per pair, chains are 30 lbs to 50 lbs per pair. Safety » Less time to install than chains which reduces the time driver is outside truck » Light weight fabric reduces potential driver injury when installing Equipment protection » AutoSock will not damage fenders if thrown from tire » No damage to tires from hooks, tensioners, or cross links » No damage to airlines or brake components Installation » AutoSock installs in approx 5 minutes per truck » Chains typically install in approx 15 to 40 mins Longevity/storage » AutoSock will not rust or corrode » Easily stored in cab of truck » If used correctly, AutoSock can last over four seasons for some drivers » AutoSock is machine washable December 4, 2017 (39AutoSock Tire Chain Alternative) Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

39VT56 TPMS Diagnostic Tool with Intellisens Universal Senso CATALOG NUMBER 39 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Huf IntelliSens Universal Sensors: • Fastest to program with 3 seconds • Copy/clone functionality • Adjustable metal valve – 0° to 36° • Only one torque – metal valves • Wireless Auto Locate • Full functionality of OE sensors • Best in market – 3 year warranty TPMS Diagnostic Tools with Intellisens Universal Sensors Included in kit are the following parts Quantity HF UVS3030 (Sensor) 315 MHz With Metal Valve Stem 4 HF UVS3031 (Sensor) 315 MHz With Rubber Valve Stem 8 HF UVS4030 (Sensor) 433 MHz With Metal Valve Stem 4 HF UVS4031 (Sensor) 433 MHz With Rubber Valve Stem 4 HF HC1000 TPMS Solution Programmer 1 Included in kit are the following parts Quantity HF UVS3030 (Sensor) 315 MHz With Metal Valve Stem 4 HF UVS3031 (Sensor) 315 MHz With Rubber Valve Stem 28 HF UVS4030 (Sensor) 433 MHz With Metal Valve Stem 4 HF UVS4031 (Sensor) 433 MHz With Rubber Valve Stem 4 HF HC1000 TPMS Solution Programmer 1 Sensor Description HF UVS2000 433 MHz With Metal Valve Stem HF UVS3030 315 MHz With Metal Valve Stem HF UVS3031 315 MHz With Rubber Valve Stem HF UVS4030 433 MHz With Metal Valve Stem HF UVS4031 433 MHz With Rubber Valve Stem HC1000 Solution Programmer w/ 20 Sensors P/N HF ISB017 HC1000 Solution Programmer w/ 40 Sensors P/N HF ISB018 New & Improved with Expanded Applications www.products.intellisens.com · Tech Support: 1-855-Huf-TPMS Bluetooth sensor to allow the use of the app on your phone to program sensors TPMS DIAGNOSTIC TOOLS HF VT46 TPMS Diagnostic Tool, 5 Year License, OBD2 Cable, 3.5” Screen, Icon Driven, Part# Lookup HF HC1000 T PMS Bluetooth Solution Programmer HF VT46 SPECIAL Buy 100 sensors mix & match and receive an HF VT46 free of charge. Available through Dec 31, 2017 on the following sensors: Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 39VT56 TPMS Diagnostic Tool with Intellisens Universal Senso MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 TRUCK PARTS SUPER STORE TM KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 JOPLIN 2424 Stephens Blvd. main 417.717.6022 fax 417.782.7126 parts 866.318.9111 October 30, 2017 (39VT56 TPMS Diagnostic Tool with Intellisens Universal Sensors) P/N HL HE-343 145mm length P/N HL HE-345 215mm length P/N HL ES-305 Closed P/N HL IN-20 12" EXTENDED AIR CHUCK, STRAIGHT CORE REMOVAL & INFLATION TIRE CHUCK • Reduces inflation & deflation time by 50% • Features a clip-on style air chuck • Made of durable brass and plastic • 1/4 female NPT allows easy attachment to air hose • Ideal for nitrogen purging and inflation • Retractable core housing allows safe removal & replacement of valve core VALVECAPPER ® PRO P/N KT 29999 • Designed by a trucker to make a difficult job easier • No more moving your rig to position valve stems just to get to the caps • No more dropped caps — holds onto caps and valve cores for removing and replacing • Longer valve cap grip works on flow-through, double seal valve caps • At 11-3/4 inches it has enough reach to get the job done • Unbreakable under normal use • Designed for use on metal and plastic valve caps • Pressureless, Unbreakable, Flexible • Don’t require additional clamps/ holders on the rim (up to an air-flexx ® length of 215 mm) • Considerably reduced risk of flat tires • Air pressure check possible at any time without removing hub caps from single wheels • Lower risk of accidents • Less fuel consumption • Less tire wear • Less repair downtime 4 TOOLS IN 1: Cap and Core Remover/Installer AIR-FLEXX VALVE EXTENSION SC CH-305 Made from hex steel SC CH-360 SC CH-315 Metal dome valve cap SC CH-335 Dual foot for hard-to-reach tractor, dual wheel trucks & bus tires. Available either closed (CH360) or open (CH360-OP) SC CH-333-LO 12” Straight-on 30° reverse angle chuck SC CH-350-LO With black polyurethane coating SC CH-330-LO 6” Straight-on 30° reverse angle chuck Ball Foot Air Chucks 3/4” European-Style Air Chuck Dual Foot Air Chuck Dual Foot Lock-On Air Chucks Dual Foot Lock-On Air Chucks SC CH-370-LO Straight-on 180° reverse angle chuck AIR CHUCKS Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==