16Zerostart Threaded Cord Nut Silicone Connector WP Male Plug ZE 3400017 • 200 watt - 120 Volt AC • UL/CSA approved • Includes 6” cordset • Quick grip handle protects hands from heat • Built-in thermostat maintains optimum temperature. Will not exceed 250°F MAGNETIC HEATER NOW STOCKING A FULL LINE ENGINE HEATERS Give One of Our 7 Locations a Call or Visit our website at www.midwestwheel.com For Applications & Part Numbers P/N Volts Amps Ga. Lengths ZE 8608059 125 15 14 (1) 7 ft. , (1)10 ft. For use with two heaters PARALLEL WEATHERPROOF “Y” CORDSET COLD WEATHER STARTING PRODUCTS BLANKET – BATTERY HEATER Thinsulate ™ thermal blanket that wraps around the battery to maintain temperature in cold or warm weather. • Warms battery core to 60-70° above ambient temperature for quick starts • Grounded cord 30" in length • 120 Volt AC operation • 5" tall, 1/2" thick Boost battery power by as much as 75% P/N Length Watts Battery Size ZE 2800063 36” 80 Series 24, 24F, 27, 27F, 74 ZE 2800071 72” 160 Truck batteries. Series-parallel systems. • Provides a secondary heat source in trucks, sleeper cabs, buses, & off-road equipment • 2-speed reversible fan motors • 20-gauge construction • Installation kit included CAB & CARGO HEATERS Model 100 Model 500 P/N Volt Capacity BTU Current (Amps) Dimensions Outlet Direction (See Photos) MODEL 100 ZE 7000101 12 17,500 3.9 7.5 x 8.6 x 7.7” Rear Top MODEL 500 ZE 7000501 12 17,500 4.4 7.6 x 8.5 x 4.3” Bottom Right ZE 7000502 12 17,500 4.4 7.6 x 8.5 x 4.3” Rear Right CATALOG NUMBER 16 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 16Zerostart 2 BLOCK HEATERS P/N Watt Volt Diameter Type Caterpillar 04-06 C11 ACERT, C13 ACERT, 04-06 C11, C13 ZE 3500075 1500 120 1-5/16” STOR Immersion 04-06 ACERT C9, C15, C16 ZE 3500077 1500 120 1-3/16” THD Immersion 04-07 C7 ACERT, 3114 (4.4L), 3116 (6.6L), 3126 (7.2L), 3126B (7.2L), CFE (Cat/Freightliner Engine), All years for previous engines prior to 2004 C7 (7.2L) ZE 3500015 1000 120 44 mm Freeze Plug ZE 3500081 1500 120 44 mm Freeze Plug 3196 ZE 3500013 1500 120 1” NPT Immersion 3208 (363 CID) Swivel Style Heater ZE 8602611 1500 120 3/4” NPT Immersion 3406E, 3456, 15.8L (600 hp) (1998 models only) ZE 3500033 1500 120 1” NPT Immersion 2007 & NEWER CAT C13 ACERT & C15 ACERT ZE 3500111 1500 120 1-3/16” #14 STOR Immersion Cummins 1987-2002 B Series: 4B3.9 & 4BT3.9 (3.9L 239 CID 4 Cyl.) Through Model Year ‘02 6B5.9 & 6BT5.9 (5.9L 359 CID 6 Cyl.) ZE 3500030 750 120 58 mm Freeze Plug 2007 ISB 6.7L & QSB (6.7L & 4.5L) ISB, QSB Series (3.9L & 5.9L 4/6 Cyl.), (Encore) ZE 3500022 750 120 3/4” NPT Immersion Signature 600, ISX, QSX (15L - 915 CID) ZE 3500038 1500 120 Plate Immersion L10 (10L, 611 CID 6 Cyl.), M11, 15M Series, QSM11 ZE 8600015 1500 120 33 mm thd. Immersion New Big Cam IV ZE 8600627 1500 120 Plate Immersion N Series (855 CID-14 litre 315, N-14-330, N14-330E N-14-460, etc.), Big Cam IV, New Big Cam IV, 88NT, 444 ZE 8601046 1500 120 Plate Immersion V903, VT903, VT350, Formula VT300 (903 CID) (alternate installation) ZE 8601267 1500 120 3/4” NPT Immersion N Series, Big Cam IV, New Big Cam IV, 88NT, (alternate installation) ZE 8601526 1500 120 Plate Immersion 2007 & Newer, ISX, QSX) ZE 3500107 1500 120 26 mm Immersion ISC, QSC Series (8.3L 505 CID), ISL Series (8.9L 543 CID) ZE 3500032 1000 120 3/4” NPT Immersion M11 (11L) (2000 and newer) ZE 3500042 1500 120 Plate Immersion Detroit Diesel 8.2L (501 CID) ZE 3500043 1000 120 3/4” NPT Immersion Series 40 (6.7L 408 CID, 7.6L 466 CID, 8.7L 530 CID) ZE 3500044 1250 120 1-1/4” NPT Freeze Plug 640 (Z-Series 8 cyl.) ZE 8605556 1500 120 1” NPT Immersion Series 40 (466 CID) (engines mfg. prior to Sept. 1993) ZE 8608512 1250 120 1-1/4” Freeze Plug P/N Watt Volt Diameter Type Ford 1460 (8.3L 505 6 cyl. - Cummins C Series) ZE 8601860 1000 120 58 mm Freeze Plug 6.6L (401 CID), 7.8L (474 CID) (engines mfg. prior to Aug. 1989) ZE 8601984 1500 120 1-1/2” Freeze Plug 6.6L (401 CID), 7.8L (474 CID) ZE 3500048 1000 120 Plate Immersion International by Navistar 2001-2003 DT466 High Torque, DT466, DT466E, HT 530, DT530 ZE 3500054 1250 120 1-1/4” Immersion 2007 & Newer MaxxForce DT, MaxxForce 9 & 10 ZE 3500163 1250 120 1-1/4” Freeze Plug John Deere All 4230, 4430, 4630, 6030, 7020, 7520 ZE 8602050 1000 120 2” Freeze Plug Power Tech: 4045, 6068 ZE 3500020 1000 120 1-5/8” thd Immersion All tractors (manufactured 1977 and later featuring large hex plug on side of engine) ZE 3500029 1000 120 1-5/8” thd Immersion Mack 865 Series, 866 & 1000 Series, EM9-400 (998 CID), E9 ZE 8601011 1500 120 3/4” NPT Immersion 2004-2006 Aset Engine Series (AL, AC + AM) (12.0L) E7 & EM7 (12.0L) ZE 8607206 1500 120 1-3/8” NPT Freeze Plug E6 (672 CID 6 cyl.) (engines w smooth bore freeze plug) ZE 8609748 1500 120 1-3/4” NPT Freeze Plug E-Tech (water pump mount) ZE 3500051 1500 120 1-3/8” Immersion Mercedes MBE4000 Series / OM460 ZE 3500080 1500 120 Plate Immersion 2004 & Newer MBE4000 Series/OM460 ZE 3500082 1500 120 Plate Immersion MBE900 Series: OM904 & OM906 ZE 3500046 1000 120 60 mm Immersion Volvo TD60 & TD61 (334 CID), TD70 & TD71 (409 CID), TD73 (427 CID) TD100 & TD101, VE10 (583 CID), TD120, TD121, TD122, TD123 (732 CID) ZE 8600287 1500 120 44 mm Immersion 2002 & Newer VED-12 ZE 3500091 1500 120 Plate Immersion P/N Watt Volt Description Thermostat ZE 3305004 2250 120 3/4” Inlet & Outlet No ZE 3308003 1500 120 5/8” Inlet & Outlet No ZE 3305056 1500 - 80° On/100° Off Yes TANK/CIRCULATION HEATERS Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 16Zerostart 3 8608865 • Transfers heat from engine coolant to the fuel just before the fuel filter for maximum efficiency • Eliminates clogged fuel filters when temperatures are below 10°F (-12°C) • Exclusive stainless steel construction with no internal welds prevents coolant from leaking into fuel • Minimal pressure drop • Can be used as a heat exchanger in some hydraulic applications • Port size: 1/2 - 14 NPT (Heavy-Duty) Specifications Pressure Drop .........................................less than 0.05 psi Maximum operating pressure ...................................75 psi Maximum operating temperature .................350°F (177°C) Test pressure .........................................................100 psi Weight (without bracket) .................................2 lbs. (907g) Lower Operating Costs by Using #2 Fuel All Year ZE 8208751 Weatherproof Cordsets & Accessories Threaded Oil Pan Heaters Without Thermostats P/N Wattage Voltage Thread Size Element Length ZE 8609802 150 120 1” NPT 6” ZE 8609683 300 120 1/2” NPT 5” • For use in water/oil • Stainless steel construction 8605688 Heavy Duty In-Line Fuel Heater P/N Applications ZE 8203237 Caterpillar, Cummins, Detroit Diesel, Ford, International Diesel Starting Fluid Systems ZE 8203237 8608652 8605254 D.O.T. Approved Replacement Starting Fluid Cylinders P/N Description Size Nozzle ZE 8200327 18 oz. 1” neck (used with most kits) 3” x 11” 1” - 20 ZE 8201277 21 oz. 1” neck (Fits Dieselmatic ® kits) 4” x 8” 1” - 20 ZE 8203903 1” standard gaskets (cork gasket flat) Pkg. of 50 1” - 20 P/N Description Voltage Cord Length Wire Gauge Receptacle Specifications ZE 8605688 Weatherproof field-wired receptacle - chrome plated 120 - - 4-hole square ZE 8605505 Weatherproof field-wired receptacle - zinc plated 120 - - 4-hole round ZE 8605645 Replacement rubber boot for WP receptacle - - - ZE 8605254 Replacement male plug for WP receptacle kit 120 - - ZE 8606005 WP silicone cordset & chrome plated receptacle 120 6 ft. 16 4-hole square ZE 8606013 WP silicone cordset & chrome plated receptacle 120 10 ft. 16 4-hole square ZE 8606048 Mounting bracket - chrome plated - - - 2 & 4 hole square ZE 8606080 Receptacle only - black - - - 4-hole square ZE 8608652 Weatherproof cordset with silicone connector 120 7 ft. 14 - ZE 8608814 Weatherproof cordset with silicone connector 120 10 ft. 14 - ZE 8608849 Weatherproof cordset with silicone connector 120 5.5 ft. 14 - ZE 8608865 Weatherproof cordset with silicone connector 120 14 ft. 14 - ZE 8608032 Square receptacle - - - 2-hole with gasket Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 16Zerostart 4 Replacement Cordsets & Accessories, Continued Series Y-Cords & Thermostats Use with one thermostat & one heater Freeze Plug Replacement Cordsets 3600082 3600006 3600023 Heavy Duty Immersion Heater Replacement Cordset Indicator Light Kit ZE 3600061 Dual Heater Sensing Indicator Light Kit 84” x 120”, 120V, Parallel Y-Cord Plug Protector ZE 3600012 • Prevents freeze up - keeps moisture out • Keeps plug contacts clean for optimum power & safety Engine Immersion Heater LED Indicator Light System Standard Kit includes weatherproof housing and 6 ft. cord ZE 3600049 Specially designed wire harness with two-light system allows operators or fleet personnel to quickly determine both power availability and heater operation • Indicator lights visible up to 150 ft. • 120 Volt - 15 Amp rating • Minimum wattage required is 150W • Chrome plated, four-hole mount square flange weatherproof receptacle with gasket P/N Length Description ZE 3600006 5 ft. Silicone cord with 90° connector (steel heaters) ZE 3600023 1 ft. Silicone cord with silicone connector (brass & aluminum heaters) ZE 3600024 1 ft. Heavy duty replacement cord P/N Length Voltage GA ZE 3600008 6 ft. 120 16 P/N Length Voltage GA Characteristics ZE 3600064 6/6 ft. 120 16 2 6 ft. lengths - flat wire ZE 3600083 - - - GM Thermostat replacement cordset with silicone connector Arctic Blue All Weather Extension Cords 12/3 SJEOW Blue/Orange w/ Primelok ® & Primelight ® P/N Length PWCLT530825 25 ft. PWCLT530830 50 ft. PWCLT530835 100 ft. • Water & Oil Resistant • Flame Retardant • Ultra Flexible • Abrasion Resistant • Nickel-Coated Brass Blades Resist Corrosion • Flexible Temperature Range (-58F - +221F) • Primelight ® Indicator Light • Primelok ® Locking Connector Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 16Zerostart 5 FUEL & FLUID WARMING PRODUCTS AR HFG-22-24 22-24” Tanks P/N Fuel Ports Coolant Ports AR I-703B 3/8” NPT 1/2” NPT AR I-703BT 1/2” NPT 1/2” NPT AR I-704B 1/2” NPT 1/2” NPT I-703BT • Stainless steel loops fit flat or curved tanks • Round fits 22” thru 29” tanks • Flat fits 14” thru 29” tanks • 5 year or 600,000 mile warranty Coolant Dam Pressure Tester In-Line Fuel Warmers Arctic Fox In-Tank Fuel Warmers • Stainless steel • All welded construction • Rotates for easy mounting In-Tank Fuel Heaters 6” Square Adapter Kit for Round Tanks AR KT-827C 22-29” Tanks P/N Hose Barb AR C-201 5/8” Round Electric Fluid Reservoir Heater • Easy Peel-And-Stick application with pressure sensitive adhesive • May be installed in sub-zero temperatures • Stainless steel construction • No moving parts • Maintenance free • Easy Installation • Includes mounting brackets Group 31 P/N Mount CCA@ 0°F CA @ 32°F Reserve Cap. Minutes DEK1131MF Top Stud 950 1170 175 DEK1131PMF Top Post 950 1140 175 • Calcium MF design Longer shelf life, less water loss,less corrosion, higher CCAs • Envelope separators Protects plates from shorts, extends life • De-mineralized acid Less water loss, gassing & corrosion • Anchor bonding Longer life in high vibration • Flush-top manifold cover No interference with hold down • Full frame grids Resists internal corrosion, delivers highest CCA per pound STARTING BATTERIES PROVIDE INSTANTANEOUS POWER 24 Month Free Replacement Warranty APPLICATIONS • Changing heater hoses, fan sensors, temperature sensors • Installing shut-off valves for fuel warmers & separators • Replacing cab heater cores • Replacing heater control valves FEATURES • Creates a vacuum, holding coolant inside the engine without hand pumping or running the engine • Quickly converts the unit from vacuum to a pressure tester • No need to drain the block for simple repairs • Coolant Filling AR T-1000 2-in-1 Shop Tool – Coolant Dam pulls a vacuum on the cooling system through the radiator cap allowing repairs to be done in less time while not completely draining the coolant out and then, changes over to a pressure tester after the repair has been completed. P/N Mount CA CCA Res. Cap Min. DEK31S925 Stud 1135 925 170 DEK31P925 Post 1135 925 170 P/N Size Volt AR 3400065 6” x 10.75” 120 GROUP 31 BATTERY 18 MONTH WARRANTY Made in the USA Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 16Zerostart 6 DIESEL FUEL TREATMENTS Winter Thaw Emergency Diesel Fuel Treatment Dissolves already gelled fuel fast. Reduces clogging of fuel filters. Prevents ice crystal build-up in fuel lines and filters by disbursing moisture. Eliminates hard starting, pounding, excessive smoking and helps improve combustion. 100% compatible with low sulfur fuel and fuel blends. Winter Pow-R ® Plus Diesel Fuel Treatment P/N Description Treats Case NA 202012 12 oz. 50 Gal. 12 NA 202032 1 Quart 250 Gal. 12 NA 202005 5 Gal. Pail 7,500 Gal. 1 NA 202055 55 Gal. Drum 82,500 Gal. 1 NA 275WPP 275 Gal. Tote 412,500 Gal. 1 ULSD compliant. Prevents gelling of diesel fuel. Prevents ice crystal formation. Reduces cold filter plug point b as much as 30°F. Helps enhance cetane. Helps improve fuel economy. Utilizes HAFI ® technology. Improves cold weather starting. Stabilizes and prevents corrosion. Helps reduce emissions. Helps improve lubricity. Winter Pow-R ® Plus for BioDiesel Diesel Fuel Treatment P/N Description Treats Case NA 202612 12 oz. 50 Gal. 12 NA 202632 32 oz. 250 Gal. 12 NA 202605 5 Gallons 7,500 Gal. 1 NA 202655 55 Gallons 82,500 Gal. 1 Ready for use in BioDiesel. ULSD compliant. Prevents gelling of diesel fuel. Prevents ice crystal formation. Reduces cold filter plug point by as much as 30°F. Helps enhance cetane. Helps improve fuel economy. Utilizes HAFI ® technology. Improves cold weather starting. Stabilizes and prevents corrosion. Helps reduce emissions. Helps improve lubricity. Winter Blend for BioDiesel Bulk Fuel Treatment Ready for use in BioDiesel. ULSD compliant. Utilizes HAFI ® technology. Highly concentrated - designed for bulk fuel tanks. Prevents gelling and ice crystal formation. Helps reduce emissions and improve fuel economy. Reduces cold filter plug point by as much as 30°F. P/N Description Treats Case NA 202132 1 Quart 25 Gal. 12 NA 202101 1 Gallon 100 Gal. 6 Winter Blend Bulk Fuel Treatment ULSD compliant. Utilizes HAFI ® technology. Highly concentrated - designed for bulk fuel tanks. Prevents gelling and ice crystal formation. Helps reduce emissions and improve fuel economy. Reduces cold filter plug point by as much as 30°F. P/N Description Treats Case NA 203025 2.5 Gal. - Concentrate 7,500 Gal. 2 NA 203055 55 Gal. 165,000 Gal. 1 Pow-R Performance ™ Diesel Fuel Enhancer Ready for use in BioDiesel. ULSD compliant. Lubricity additive. Cetane improver. Maximizes fuel lubrication. Increases power. Stabilizes stored fuel. Reduces Nox. Cleans injectors. Decreases fuel consumption. P/N Description Treats Case NA 208005 5 Gallons 7,500 Gal. 1 P/N Description Treats Case NA 203605 5 Gallon 7,500 Gal. 1 NA 203655 55 Gallon 82,500 Gal. 1 PENRAY WINTER CHEMICALS Nox-Ice Gas Line Antifreeze Windshield Spray De-Icer Contains isoproply alcohol. Absorbs twice as much moisture as methanol based products. For gasoline, gasohol, and diesel engines. Excellent in all fuel injected engines. P/N Description Case NA 5113 12 oz. 24 NA 5155 55 Gal. 1 P/N Description Case NA 5216 (05346) 12.3 oz. 12 Defrosts and melts ice from windshields, headlights and windows. Thaws locks in extreme cold weather. Great for removing summer bugs from glass areas. The first & only test strip designed for all heavy-duty coolant types. A quick & effective way to test your cooling system in both conventional & extended life coolant. 25 test strips/bottle Universal 3-Way Test Strips NA TS200 Premium Starting Fluid P/N Description Case NA 5315 11 oz. 12 Extremely high ether content. Gives fast and easy starts in seconds. For use in gasoline or diesel engines. Ideal for cars, trucks, tractors, generators, buses, marine engines,outboards and power mowers. Saves batteries, starters and engine wear. Also provides upper cylinder lubrication. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 16Zerostart 7 BEST-SELLING DIESEL ADDITIVE IN THE U.S.! Microbes in the form of bacteria and fungus are present in all diesel fuels. Long periods of fuel storage can create ideal opportunities for microbes to grow in fuel tanks. The first indication of microbial contamination is mucous-like accumulations on fuel-filters and increased requirements for fuel-filter replacement. Microbes can only be removed from the fuel system by use of a diesel fuel biocide. DIESEL KLEEN + CETAIN BOOST is the premier “performance” product on the market. DIESEL KLEEN is loaded with cetane, detergency and lubricity additives to keep your diesel engine running at peak performance. Contains Slickdiesel for maximum fuel lubrication. POWER SERVICE DIESEL ADDITIVES ULSD APPROVED The Premier “Performance” Product P/N Size Treats Treat Ratio PS 03012-09 12 oz. Up to 40 Gallons 1:400 PS 03016-09* 16 oz. Up to 40 Gallons 1:500 PS 03025-12 32 oz. Up to 100 Gallons 1:400 PS 03064-06 64 oz. Up to 25 Gallons 1:500 PS 03080-06* 80 oz. Up to 250 Gallons 1:400 PS 03850-02 2.5 gal. Up to 3,750 Gallons 1:1500 *While qty lasts DIESEL KLEEN ® +CETANE BOOST ® P/N Size Treats Treat Ratio PS 01012-09 12 oz. 40 Gallons 1:500 PS 01025-12 32 oz. 100 Gallons 1:400 PS 01064-06 64 oz. 250 Gallons 1:500 PS 01080-06* 80 oz. 250 Gallons 1:400 PS 01050-02 2.5 gal. 3,750 Gallons 1:1500 PS 01055-01 55 Gal. Drum 82,500 Gallons 1:1500 DIESEL FUEL SUPPLEMENT ® +CETANE BOOST ® *While qty lasts BENEFITS Prevents fuel gelling Protects against fuel-filter icing Boosts cetane for faster cold starts Contains Slickdiesel ® Lubricator to protect fuel pumps and injectors from increased wear caused by poor quality Ultra Low Sulfur Diesel (ULSD) fuel Effective in all diesel fuels including ULSD and biodiesel blends Diesel Fuel Supplement ® +Cetane Boost ® is a winterizer/antigel that is used in the winter to prevent fuel gelling and protect against ice and wax from plugging fuel-filters. It provides trouble-free winter operation for diesel fuel. P/N Pack Treats Treat Ratio 1:400 PS 08025-12 32 Oz. 30-75 Gallons PS 08064-06 64 Oz. 80-160 Gallons PS 08080-06* 80 Oz. 100-200 Gallons P/N Size Treats PS 09016-09 16 oz. Up to 880 gallons PS 09128-04 1 gal. Up to 7,000 gallons DIESEL 9•1•1 ® Diesel 9•1•1 ® is a winter emergency product used to reliquefy gelled fuel and de-ice frozen fuel-filters. This Winter Rescue Formula restores the flow of fuel to the engine. Use this product if your vehicle will not start or gain power. BENEFITS Reliquefies gelled fuel De-ices frozen fuel-filters Removes water Prevents fuel-filter icing Contains Slickdiesel ® Lubricator to protect fuel pumps and injectors from increased wear caused by Ultra Low Sulfur Diesel (ULSD) fuel Effective in all diesel fuels, including ULSD and biodiesel blends In a winter emergency DIESEL 911 ® Use Diesel 911 to reliquefy gelled fuel and de-ice frozen fuel- filters if your vehicle will not start or gain power in cold weather. *While qty lasts BIO KLEEN ® DIESEL FUEL BIOCIDE Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15LiftGate Parts082105132021 LIFTGATE PARTS PH 15-335 Single Pole Plug $13.64 PH 15-326 Dual Pole Socket $17.69 PH 15-320 Single Pole Socket $12.83 4 IN 1 ASSEMBLIES Back DUAL POLE NOSEBOX LIFTGATE DUAL POLE INSTALLATION OR CONVERSION KIT TC 670-28 2-Pole Power Take-Off Connector Socket $11.36 PH 15-328 Vertical dual pole socket $17.60 TC 670-29SG 2-Pole Power Take-Off Plug $11.42 PH 15-338 4 ga. vertical dual pole plug $15.92 PH 30-2251 12’, ABS with zinc die-cast plugs, single pole, rubber air lines PH 16-77526 $31.19 STA-DRY ® nosebox w/ dual pole socket* PH 15-327 Liftgate Dual Pole Conversion Kit $302.21 PH 15-327-150 Liftgate Dual Pole Conversion Kit w/ 150 amp circuit breaker $367.45 *Assembly includes gasket and grommet Improve conductivity & maintain a secure ground for your liftgate application! Everything you need for a dual pole installation or a single to dual pole conversion! P/N Length Lead Length/Connectors Style TC 7DDB222MW 12' 12" DOUBLE DUAL x 12" DOUBLE DUAL Coiled with WeatherSeal $170.01 TC 7DDB522MW 15' 12" DOUBLE DUAL x 12" DOUBLE DUAL Coiled with WeatherSeal $186.34 TC 670-DDSG - - Plug Assembly $17.54 DOUBLE DUAL ™ ONE-PLUG SOLUTION! A patent pending, dual pole plug that is universally configured to function with both vertical and horizontal socket designs. One plug handles all your dual pole application needs! SIMPLIFIED CONNECTIONS - eliminates the need to stock multiple dual pole plug and cable assemblies. Simplify fleet equipment with this universal plug option. VERSATILITY ON THE VEHICLE - Accommodates bi-directional connectivity regardless of the dual pole configuration used on either the tractor or trailer. PRICING GOOD THROUGH AUGUST 31, 2021 CATALOG NUMBER 15 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Dual Pole PERMACOIL ™ Single Pole DUAL POLE 2/4 ga. Fine Stranded Copper PH 23-2626 15’, 1 ground, 1 hot $175.23 DUAL POLE PERMACOIL ™ 2/4 ga. Fine Stranded Copper PH 23-2316 12’, 1 ground, 1 hot $137.21 PH 23-2616 15’, 1 ground, 1 hot $141.78 SINGLE POLE 1/4 ga. Fine Stranded Copper PH 23-4325 12’, 1 hot $81.88 PH 23-4625 15’, 1 hot $81.49 STRAIGHT - SINGLE POLE 1/4 ga. Fine Stranded Copper PH 23-2051 12’, 1 hot $64.63 PH 23-2071 15’, 1 hot $67.85 STRAIGHT - DUAL POLE 2/4 ga. Fine Stranded Copper PH 23-2251 12’, 1 ground, 1 hot $115.51 PH 23-2271 15’, 1 ground, 1 hot $134.24 Dual Pole ZINC DIE-CAST LIFTGATE CHARGING CABLES Straight PH 15-336 Dual Pole Plug $16.03 $230.91 Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

15Behind the Cab ISOFlex (Straight- ISO, Yellow) P/N Description PH 31-2073 15’ w/ Metal Plugs ELECTRICAL ASSEMBLIES ABS Lectraflex (Straight) P/N Description PH 30-2050 12’ w/ Permaplugs PH 30-2051 12’ w/ Metal Plugs PH 30-2054 12’ w/ QCP PH 30-2057 12’ w/ Molded Ends (M7) PH 30-2070 15’ w/ Permaplugs PH 30-2071 15’ w/ Metal Plugs PH 30-2074 15’ w/ QCP PH 30-2077 15’ w/ Molded Ends (M7) (Note: 8’, 10’, 20’ available. See catalog) Non ABS Duraflex (Straight) P/N Description PH 22-2050 12’ w/ Permaplugs PH 22-2071 15’ w/ Metal Plugs AVAILABLE PLUG OPTIONS FOR ELECTRICAL ASSEMBLIES *Not all plugs available on all assemblies QCP ™ assemblies are field repairable in seconds! QCP ™ Quick-Connect Plug 16-125 Insert Cartridge Permaplug ™ Zinc Die-Cast Plug PH 5-750 - Replacement gasket for Weather-Tite ™ Permaplug ™ CATALOG NUMBER 15 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ • Supplemental retention system that securely holds the trailer plug in the socket • Reduces electrical and lighting flickers • Universal design allows it to be installed on standard and large flange sockets PLUGSAVER AUT179.1019 BEHIND THE CAB PRODUCTS Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 15Behind the Cab Page 2 ABS Lectracoil P/N Description PH 30-9320 12’ w/ Permaplugs (3yr warranty) PH 30-9321 12’ w/ metal plugs PH 30-9620 15’ w/ Permaplugs (3yr warranty) PH 30-9621 15’ w/ metal plugs PH 30-9624 15’ w/ QCP (5 yr warranty) PH 30-9920 15’ w/ 48” lead w/ permaplugs (3yr warranty) PH 30-9921 15’ w/ 48” lead w/metal plug PH 30-9924 15’ w/ 48” lead w/ QCP (5 yr warranty) (Note: other lengths and plug options available) ELECTRICAL ASSEMBLIES CONT’D ABS Permacoil P/N Description PH 30-4321 12’ w/ metal plugs PH 30-4324 12’ w/ QCP (3 yr warranty) PH 30-4327 12’ w/ molded ends (M7) PH 30-4621 15’ w/ metal plugs PH 30-4624 15’ w/ QCP (3 yr warranty) PH 30-4627 15’ w/ molded ends (M7) PH 30-4920 15’ w/ 48” lead w/ permaplugs PH 30-4921 15’ w/ 48” lead w/ metal plugs PH 30-4924 15’ w/ 48” lead w/ QCP (3 yr warranty) PH 30-4927 15’ w/ 48” leave w/ molded ends (M7) (Note: Other lengths and plugs available) ISO Coil (Yellow ISO Cable) P/N Description PH 31-9323 12’ w/ metal plugs PH 31-9623 15’ w/ metal plugs (Note: other lengths available) Light Duty Cables P/N Description PH 19-6708 8’ 6way coil PH 19-6710 10’ 6way coil PH 19-6712 12’ 6way coil PH 19-6715 15’ 6way coil PH 19-4710 10’ 4way coil PH 19-4712 12’ 4way coil PH 19-4715 15’ 4way coil (Note- other lengths available, all have thermoseal plugs) Dual Pole Cable P/N Description PH 23-2626 15’ 100amp Permacoil PH 23-2616 15’ 100amp (Note: other jacketing options and lengths available) Single Pole Cable P/N Description PH 23-4325 12’ 100amp PH 23-4625 15’ 100amp Air & Electrical Assemblies (3-in-1) P/N Description PH 30-2150 12’ ABS w/ Weather-Tite ™ Permaplugs ™ PH 30-2151 12’ ABS w/ metal plugs PH 30-2154 12’ w/ with QCP PH 30-2155 12’ ABS w/ QCMS2 ™ & QCP ™ PH 30-2170 15’ ABS w/ Weather-Tite ™ Permaplugs ™ PH 30-2171 15’ ABS w/ metal plugs PH 30-2174 15’ ABS w/ QCP PH 30-2175 15’ ABS w/ QCMS2 ™ & QCP ™ (Note- Non ABS versions available) Non-ABS Permacoil P/N Description PH 24-4321 12’ w/ metal plugs PH 24-4320 12’ w/ Permaplugs PH 24-4621 15’ w/ metal plugs PH 24-4620 15’ w/ Permaplugs (Other lengths, plugs, jacketing materials available) Non-ABS Duracoil P/N Description PH 22-9320 12’ w/ Permaplugs PH 22-9321 12’ w/ metal plugs PH 22-9620 15’ w/ Permaplugs PH 22-9621 15’ w/ metal plugs PH 22-9720 15’ w/ 72” lead and Permaplugs PH 22-9921 15’ w/ 48” lead and Permaplugs GOOD GOOD BEST BEST Good recoil memory, chemical and abrasion resistan ce Good recoil memory, chemical and abrasion resistance Excellent recoil memory, chemical and abrasion resistance Excellent recoil memory, chemical and abrasion resistance Spiral Wrap Sold Per Foot P/N Description PH 5-534 1" I.D. PH 5-536 1 3/8" I.D. NOW includes a set of red & blue rubber air lines PH 5-750 Replacement gasket for Weather-Tite ™ Permaplug ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 15Behind the Cab Page 3 4 Way Plug/Socket P/N Description PH 15-410 4 way plug PH 15-430 4 way plug w/ cable guard PH 15-400 4 way socket, split pin, wire insertion Plug/Socket Brushes P/N Description PH 15-121 Plug brush (shaped like socket) GR183-6561 7 Pole Plugs & Socket Brush Socket Accessories P/N Description PH 15-640 4 & 6 way socket boots PH 15-740 7 way socket boot PH 15-788 Socket mounting bracket PH 15-795 Foam socket seal ISO Connectors P/N Description PH 15-830 Metal ISO plug w/ cable guard PH 16-822 Sta-Dry ISO socket w/ ring termination PH 16-826 QCS ISO socket w/ bullet terminals PH 16-7422 90 degree QCS ISO harness 48” blunt cut Liftgate Plugs & Sockets P/N Description PH 15-335 Single pole plug PH 15-320 Single pole socket PH 15-336 Dual pole plug PH 15-326 Dual pole socket TC 670-28 Dual pole socket (vertical) TC 670-29SG Dual pole plug (vertical) 6 Way Plug/Socket P/N Description PH 15-610 6 way plug PH 15-630 6 way plug w/ cable guard PH 15-600 6 way socket, split pin, wire insertion 7 Way Plugs P/N Description PH 15-730 Metal plug w/ cable guard PH 16-730 Permaplug PH 16-125 QCP Insert 7 Way Sockets P/N Description PH 15-720 Metal socket w/ wire insertion PH 16-720 Sta-Dry Socket w/ wire insertion PH 16-722 Sta-Dry socket w/ ring termination PH 16-726 QCS socket, solid brass pins, w/ clip PH 16-724 QCS2 Socket, solid brass pins, no clip 7 Way QCS Harness P/N Description PH 16-7421 90 degree blunt cut QCS (includes socket) PH 16-7403 Straight back 48” blunt cut QCS2 (includes socket) SOCKET BREAKERS AND NOSES BOXES 7 Way STA-DRY Socket Breakers P/N Description PH 16-762 20 amp breakers, split pin PH 16-763 30 amp breakers, split pin PH 16-760 w/o breakers, split pin STA-DRY S7 P/N Description PH 16-9500 w/o nosebox PH 16-9510 Nosebox w/o circuit breakers PH 16-9520 Nosebox w/ 20 amp circuit breakers PH 16-9530 Nosebox w/ 30 amp circuit breakers (MANY other socket breakers available, such as 28 pin style, see catalog for details) ELECTRICAL CONNECTORS The industry’s ONLY swivel socket designed to completely eliminate pull-away damage! Socket swivels 80° side to side (40° each way) PH 5-750 Replacement gasket for Weather-Tite ™ Permaplug ™ PH 54-130 PH 54-140 Solenoids P/N Description PH 54-130 12v, 80amp PH 54-140 12v, 80amp, continuous duty 7 Way Metal Extended Barrel Nose Box P/N Description PH 15-762 20 amp breakers, split pin PH 15-763 30 amp breakers, split pin PH 15-760 w/o breakers, split pin Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 15Behind the Cab Page 4 Pogo stick shown with clamp CABLE AND SUPPORT ACCESSORIES Stow-A-Way P/N Description PH 15-041 1 plug, 2 glad hand holder PH 15-042 2 plug, 2 glad hand holder Clip P/N Description PH 17-161 4” black, large snap-on clip with wire gate Cable Clamp Holder P/N Description PH 5-5008 Cable Clamp Holder Tracker Bars P/N Description PH 17-149 Tracker bar kit w/ 43” bar & 17-148 PH 17-249 Tracker bar kit w/ 36” bar & 17-148 TRACKER BAR SPRING KITS P/N Description PH 17-145 25" heavy duty spring, with QWIK-SNAP ™ PH 17-148 20" heavy duty spring, with QWIK-SNAP ™ PH 17-1481 20.5" extra heavy duty spring, with QWIK-CLAMP ™ PH 17-1482 25" extra heavy duty spring, with QWIK-CLAMP ™ PH 17-1487 20" heavy duty spring, with U-bolt holder PH 17-1488 20.5" extra heavy duty spring, with cable clamp PH 17-420 16" dual springs, with QWIK-SNAP ™ MAXXClamp P/N Description TA 451169 MAXXClamp Twist Lock Hose Clamp, 3/8” TEC-CLAMP with E-coated clip TC 9887 2 Hole TC 9888 3 Hole TC 9889 4 Hole TEC-360° Clamp TC 9890ST360 3-in-One Airpower Line TEC-360° Clamp TC 9888ST360 3-Hole TEC-360 ™ Clamp QWIK-CLAMP ™ PH 17-180 with insert PH 17-181 without insert Hose Holders Qwik Snap PH 17-152 2 hose qwik snap PH 17-153 3 hose qwik snap PH 17-154 4 hose qwik snap Pogo Sticks & Accessories P/N Description TC 9400E Pogo stick yellow dichromate w/o clamp TC 9400G Pogo stick chrome w/o clamp TC 9400H-2 Pogo stick w/clamp TC 9400H-1 Pogo stick w/o clamp Circuit Breakers P/N Description PK 54-115P 15 amp circuit breaker PK 54-120P 20 amp circuit breaker PK 54-130P 30 amp circuit breaker Junction Box P/N Description PH 15-961 Clear-Vu Junction Box MD BE22070 Junction Box SOCKET BREAKERS AND NOSES BOXES CONT’D Qwik Snaps snap together in seconds, no messing with bolts and screws! Hose Spacers P/N Description TC 940-5 Two 3/8” I.D.” hoses TC 940-58 Two 1/2” I.D.” hoses Nose Boxes P/N Description PH 15-769 1 -7/8” metal nose box kit PH 15-775 3-1/8” metal nose box kit PH 16-775 Sta-Dry single cavity nose box 3.5” deep PH 16-777 Sta-dry dual cavity nose box 3.5” deep PH 17-1488 Hose Separator P/N Description TA 451170 3-in-1 Hose Separator Dual functionality - Can be converted from a 1, 2, or 3-hose holder to a cable clamp for a 3-IN-1 by removing the insert NEW! Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 15Behind the Cab Page 5 WIRE AND CABLE COILED AIR GRIPS DURAFLEX ™ P/N Stranding 12 ga. Stranding 10 ga. 7 Conductor 6/12, 1/10 ga. .640 O.D. PH 3-224 65 x 30 105 x 30 7 Conductor 6/12, 1/12 ga. .570 O.D. PH 3-244 415 x 30 65 x 30 6 Conductor 6/14 ga. .550 O.D. PH 3-204 41 x 30 - 6 Conductor 6/14 ga. .550 O.D. PH 3-194 41 x 30 - Battery Cable P/N Size/Package Stranding Color PH 3-504 4 ga. spool 133 x 24 Black PH 3-503 4 ga. spool 133 x 24 Red PH 3-505 2 ga. spool 133 x 27 Red PH 3-506 2 ga. spool 133 x 27 Black PH 3-509 1/0 ga. spool 133 x 21 Red PH 3-510 1/0 ga. spool 133 x 21 Black PH 3-511 2/0 ga. spool 259 x 23 Red PH 3-512 2/0 ga. spool 259 x 23 Black Sliding Axle Spring Kits And Replacement Hose Tender Springs P/N Description PH 17-183 3 hose sliding axle kit: 16” spring, frame clip, 3 hose qwik snap PH 17-182 2 hose sliding axle kit: 16” spring, frame clip, 3 hose qwik snap PH 17-103 3” spring with frame clip ¾â€ OD PH 17-106 6” spring PH 17-111 11” spring PH 17-116 16” spring PH 17-120 20” spring PH 17-121 20.5”, extra heavy-duty, for use with combination electrical and air assemblies and with hydraulic lines PH 17-124 25” extra heavy duty spring, for combination assemblies and hydraulic lines, 0.93” O.D. PH 17-125 25” heavy duty spring, for ABS coiled assemblies, 0.90” O.D. P/N Outside Diam. Length TC 912 1” 13” TC 913 1-1/16” 16” TC 910 1-1/8” 25-1/2” (NOTE: all springs are galvanized hard drawn wire per, 1” OD) All sold per foot CABLE AND SUPPORT ACCESSORIES CONT’D Longer Lasting Springs! Coiled Air Grips P/N Description PH 12-600 Pair of aluminum coiled air grips, red/blue anodized TC 1011G Glad Grip - Use to protect airlines & make gladhand connections easier. Each kit consists of 2 red Glad Grip halves, 2 blue Glad Grip halves, 2 plated steel couplings &, 12 fastening screws. TC 1011FG Flex Grip - Use to protect airlines & make gladhand connections easier. With new flexible rubber grip. MAXXGrip P/N Description TA 441228 Gladhand Dura-Grip, Display 2 Pack, 1 Service and 1 Emergency TC 1011G PH 12-600 Hose Holders Bolt Together P/N Description TC 94-0001 Heavy duty 3 hole support clamp TC 94-0002 “Beefy” 3 hole support clamp Hose Holders Bolt Together P/N Description PH 17-156 2 hose bolt together PH 17-157 3 hose bolt together PH 17-158 4 hose bolt together Prevents scuffs and marring on the back of the cab by extending the cables out and away from the back of the tractor. X-TEND ™ Tracker Bar Extension PH 17-3500 for 3/4" diameter tracker bars PH 17-3501 for 1" diameter tracker bars PH 17-3000 for 3/4” diameter tracker bars PH 17-3001 for 1” diameter tracker bars X-TEND ® DAY CAB TRACKER BAR EXTENSION Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 15Behind the Cab Page 6 AIR ASSEMBLIES *Coiled air hoses contain substantially more hose than stated working length. Coiled Air P/N Description 12’ Working Length: PH 11-712 Pair (red & blue) GR181-0012-R Red (emergency) coil only GR181-0012-B Blue (service) coil only Coiled Air P/N Description 15’ Working Length* PH 11-715 Pair (red & blue) PH 11-717 Red (emergency) coil only PH 11-718 Blue (service) coil only 5th Wheel Slider Air Coil P/N Description AUTKP155 54” Air Coil AUTKP155K 54” Air Hose Kit PH 11-302 60” Air Coil HH RK-01960 120” Air Coil ARMORCOIL ® Armored Nylon Aircoils P/N Description TC 17A15H 15’, 12” leads TC 17A15-40H 15’, 48” leads MAGNUM ® Dual-line Armorcoil System P/N Description TC 17M15H 15’, 12” leads Coiled Air with Gladhands P/N Description PH 11-3159 15' Pair, with 2 gladhands Rubber Air (Straights) P/N Description PH 11-81120 12’ set PH 11-81150 15’ set PH 11-81200 20’ set Polar Air (coils) P/N Description PH 11-5120 12’ set PH 11-5150 15’ set PH 11-5400 15’ set w/ 40” lead Power Grip P/N Description PH 11-3150 15' Pair (red and blue) PH 11-3170 15' Red (emergency) coil only PH 11-3180 15' Blue (service) coil only PH 11-3400 15' Pair (red and blue), with 40" lead (Note: singles and universal (black) grips available) 2 Year Warranty Stays flexible at -85˚ F! Heavy Duty Coiled Air P/N Description 15’ Working Length* PH 11-315 Pair (red & blue) PH 11-317 Red (emergency) coil only PH 11-318 Blue (service) coil only Heavy Duty Coiled Air w/ Power Grip P/N Description 15’ Working Length with 40’ Lead* GR181-0015-40R Red (emergency) coil only GR181-0015-40B Blue (service) coil only GR181-0015-40 Pair (red & blue) Red & blue rubber lines, with red & blue grips GOOD GOOD BEST BETTER Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 15Behind the Cab Page 7 PROB Debris causin and tim SOLU 3.5" 3.61" • Debris is trapped in the Quick-Change Cartridge of the AIR DEFENSE™ System, reducing debris entering the Part No. Description 12-815 AIR-DEFENSE™ System 12-035 Quick-Change Cartridge - Replacement Filter TRAILER AIR BRAKE LINE FILTRATI AIR-DE with Q AIR-DEFENSE SYS TM WITH QUICK-CHANGE CAR WE MAKE PRODUCTS THAT MAKE A DIFFERE Bulkhead Shut Off Glad-Hands P/N Description PH 12-306 Aluminum service, blue, ½â€ air tube PH 12-308 Aluminum emergency, red, 3/8” air tube AIR-DEFENSE SYSTEM WITH QUICK-CHANGE CARTRIDGE P/N Description PH 12-815 AIR-DEFENSE ™ System PH 12-035 Quick-Change Cartridge - Replacement Filter Glad-Hand Seals P/N Description PH 12-012 Wide lip rubber PH 12-0161 Blue poly PH 12-0162 Red poly PH 12-0163 Black poly PH 12-0167 Black poly w/ flaps PH 12-038 Filter screen for standard gladhands Glad-Hand Seals P/N Description MD 10024 Gladhand Protect-O Seal TC 101119B Blue w/ 1-1/4” traditional sealing lip TC 101119R Red w/ 1-1/4” traditional sealing lip TC 101119BRP Blue/Red, 2 pair GG 0002B Blue w/ filter GG 0002R Red w/ filter Surface Mount Shut-Off Glad-Hands P/N Description PH 12-338 Emergency, red, 3/8’’ female pipe thread PH 12-336 Service, blue, 3/8’’ female pipe thread Glad-hand Lock P/N Description TC 1011LK Lock Qwik-E Glad-Hands P/N Description PH 12-206 ½ female pipethread, w/o screen PH 12-236 Angle mount ¾ female pipe thread bottom port w/o screen Cast Iron Glad-Hands P/N Description PH 12-406 Service, blue poly seal PH 12-408 Emergency, red poly seal Anodized Swinger Glad-Hands P/N Description PH 12-4506 45 degree with service gh PH 12-4508 45 degree with emergency gh (Other port and screen options available. All are anodized w/ poly seal) GLAD-HANDS Anodized Glad-Hands P/N Description PH 12-00623 Service straight, blue w/ poly seal PH 12-00823 Emergency straight, red, w/ poly seal PH 12-13623 Trailer Mount, Service, blue, bottom port, anodized, 3/8” female pipe thread PH 12-13823 Trailer Mount, Emergency, red, bottom port, anodized, 3/8” female pipe thread Standard Glad-Hands P/N Description PH 12-006 Service straight, blue PH 12-008 Emergency straight, red PH 12-010 Universal PH 12-136 Service angle mount, blue, bottom port PH 12-138 Emergency angle mount, red, bottom port (Other options available, see catalog) Debris is trapped in the Quick-Change Cartridge of the AIR DEFENSE ™ System, reducing debris entering the trailer air lines and brake valves Intended to be installed between the trailer gladhands and the air lines to the brake valves. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

11PAI Flywheel Housings130003042021 CATALOG NUMBER 11 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ PAI Flywheel Housings TWO YEAR UNLIMITED MILEAGE WARRANTY P/N PA1360470 OEM#: CAT1694153, CAT 1569783, CAT 3044191 SAE#1 Application: Caterpillar Engine C15 P/N PA1060009 OEM#: CUM3680063 SAE#1 Application: Cummins Engine ISX P/N PA1360471 OEM#: CAT1605142 SAE#2 Application: Caterpillar Engine 3100, C7 P/N PA1360473 OEM#: CAT1302802 12mm Mounting Holes SAE#1 Application: Caterpillar Engine 3406E, C15, C16, C18 P/N PA1060000 OEM#: CUM3931716 SAE#2 Application: Cummins Engine 4B,6B P/N PA1060003 OEM#: CUM3036011 SAE#1 Application: Cummins Engine 855, N14 P/N PA1060006 OEM#: CUM3882591 Starter Opening 3 5/8” SAE# 1 Application: Cummins Engine L10, M11, ISM CATERPILLAR CUMMINS Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

11Clutch Guide New This clutch system offers the durability and performance necessary to withstand the high actuation conditions and associated with automated transmission systems. This clutch has been developed for a wide range of customer applications from Linehaul to Vocational to meet with the many specific automated transmissions offered by Eaton. CLUTCH & GEARING GUIDE MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 TRUCK PARTS SUPER STORE TM KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 JOPLIN 2424 Stephens Blvd. main 417.717.6022 fax 417.782.7126 parts 866.318.9111 August 2021 (11Clutch Guide New) Clutch Parts & Accessories ∙ Flywheels ∙ Transmissions ∙ Differentials At the front of the UltraShift 6, 10 and 13-speed transmissions is the UltraShift DM clutch, which engages and disengages without an in-cab pedal. The AutoClutch uses a traditional two-plate configuration for heavy duty and single-plate for medium duty, complete with soft rate dampers and ceramic facings for smooth engagement. UltraShift ™ DM Clutch Eliminates the need for a clutch pedal and helps to maximize clutch life. UltraShift PLUS ECA (Electronic Controlled Actuator) MC MAX121000X 2”-10 Spine ∙ 1750ft/lb MC MAX122002X 2”-14 Spine ∙ 1850ft/lb AUTOMATED MANUAL TRANSMISSION CLUTCHES CATALOG NUMBER 11 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ *New flywheel required for every install *Eaton software required to remove and install unit P/N OE Reference Description Detroit D12 Transmission MC ANK4489CL K-4489 (Eaton) Single-Plate, 18 Involute Spline, Organic / 6-Spring / 1850 Torque Volvo I-Shift / Mack mDrive (13L Engine, Volvo I-Shift and Mack mDrive) MC MAX104461-1 104461-1 (Eaton) / 3400 700 359 (Sachs) Single-Plate, 24 Involute Spline, Organic / 6-Spring / 1850 Torque MC A-1001 - Clutch Actuator for MC MAX104461-1 430mm x 50mm Stamped Steel Clutch *New inertia brake may be required P/N GP K3637 *Eaton software required to remove and install unit Offered in these torque ranges: 1860 2050 2250 • OE supplied friction material USA made • Springs are OE quality USA made • Castings and stamping are USA made • All components are 100% new • New center plates Proudly Made in the USA • Self aligning release bearing • CNC machined housing • 6 coil spring with 3 assist spring technology • 2 year / 200,000 mile warranty for line haul applications or 1 year / 100,000 mile warranty for severe duty type applications New and Reman Available MC MAX3400300063X 1700 MAX TORQUE MC MAX3400300193X 1 860 MAX TORQUE MC MAX3400300195X 2050 MAX TORQUE MaxHD Sachs Reman Clutch Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 11Clutch Guide New 2 Clutch Guide MC MAX1076835(X) New/Reman MC MAX10723722(X) New/Reman MC MAX10734212(X) New/Reman MC MAX10805059B(X) New/Reman Manual Adjust MaxHD NEW Manual Adjust MaxHD REMAN Self Adjust SOLO MaxHD REMAN MaxHD Sachs REMAN CAT, CUMMINS, DETROIT 14” X 1-3/4” 10 SPLINE Single Plate, Flat Flywheel MC MAX1076835 MC MAX1076835X 2 Plate, Flat Flywheel MC MAX10723722 MC MAX10723722X 14” X 2” 10 SPLINE 2 Plate, Flat Flywheel MC MAX10734212 MC MAX10734212X 14” X 2” 10 SPLINE 2 Plate, Pot Type Flywheel MC MAX10805059B MC MAX10805059BX CAT, CUMMINS, DETROIT, VOLVO, INTERNATIONAL, MERCEDES 15-1/2” X 2” 10 SPLINE STANDARD DUTY 2 Plate, Flat Flywheel MC MAX10839182 MC MAX10839182X HEAVY DUTY 2 Plate, Flat Flywheel MC MAX10892582 MC MAX10892582X MC MAX10970182X MC MAX3400300063X MC MAX10892582H MC MAX10892582HX MC MAX10839174 MC MAX10839174X MC MAX3400300193X SUPER HEAVY DUTY MC MAX10839193H MC MAX10839193HX MC MAX10939193HX 2 Plate, Flat Flywheel MC MAX10892525 MC MAX10892525X 500+ HP MC MAX10970125X MC MAX3400300195X MC MAX10892525H MC MAX10892525HX MACK HIGH TORQUE MC MAX10893551X 2 Plate, Flat Flywheel MC MAX10893591 MC MAX10893591X MC MAX10993591X All MaxHD Clutches have 3 zerk fittings in housing equivalent to 208 and 209 Eaton Series Clutches 2 Year, Unlimited Mileage Warranty UltraShift ™ DM Clutch Eliminates the need for a clutch pedal and helps to maximize clutch life. UltraShift PLUS ECA (Electronic Controlled Actuator) MC MAX121000X 2”-10 Spine ∙ 1750ft/lb MC MAX122002X 2”-14 Spine ∙ 1850ft/lb AUTOMATED MANUAL TRANSMISSION CLUTCHES *New inertia brake may be required P/N GP K3637 *Eaton software required to remove and install unit *New flywheel required for every install *Eaton software required to remove and install unit Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 11Clutch Guide New 3 MC MAX10892525(X) New/Reman MC MAX10892525H(X) New/Reman MC MAX10839193H(X) New/Reman MC MAX10939193HX Reman MC MAX10892582(X) New/Reman MC MAX10970182X Reman MC MAX10892582H(X) New/Reman MC MAX10839182(X) New/Reman MC MAX10839174(X) New/Reman MC MAX10893591(X) New/Reman MC MAX10993591X Reman MC MAX10893551X Disc Springs Disc Facing Min. Flywheel Bore Opening Plate Load Max Torque (Ft./Lbs.) 8 4 Pad Ceramic Button 7” 2800 620 8 3 Pad Ceramic Button 7” 2400 860 8 3 Pad Ceramic Button 7” 2800 900 8 4 Pad Ceramic Button 7” 3600 1400 8 4 Pad Ceramic Button 7” 3600 1400 7 (Sachs 6) 4 Pad Ceramic Button 10” 4000 1700 7 6 Pad Ceramic Button 10” 4000 1860 10* (Sachs 6) 4 Pad Ceramic Button 8.5” 4000 1860 10* 6 Pad Ceramic Button 8.5” 4000 2050 7 6 Pad Ceramic Button 10” 4000 2250 7 (Sachs 6) 6 Pad Ceramic Button 10” 4000 2050 6 w/ Spline Saver 6 Pad Ceramic Button 10” 4000 2250 9 4 Pad Ceramic Button 10” 4000 1860 9 6 Pad Ceramic Button 10” 4000 2050 AUTOMATED MANUAL TRANSMISSION CLUTCHES MCI, Prevost, Van Hool and Serta Coaches SCS3400 000 358 Newell Coaches SCS3400 654 141 Bearing and Roller fork Kit SCS3189 600 001 ZF-AS TRONIC AND FREEDOMLINE TRANSMISSIONS *Use 7 Spring with FRO Transmission to avoid engine idle rattle Proudly Made in the USA Detroit D12 and Volvo I-Shift / Mack mDrive: See Front Page Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 11Clutch Guide New 4 PARTS & ACCESSORIES CLUTCH LUBE ASSEMBLIES MC GH8 8" Lube Tube Assembly MC GH12 12" Lube Tube Assembly Seal P/N O.D. I.D. Width Seal Temp. Rating Grease Temp. Rating Black Nitrile NCB203-FF.4 1.58" .67" .47" +248°F +347°F NCB205SS.4 2.05" .99" .59" +248°F +347°F NCB206FF 2.45" 1.18" .63" +248°F +347°F NCB206SS 2.45" 1.18" .63" +248°F +347°F NCB305DD 2.45" .99" .67" +248°F +347°F NCB305SS 2.45" .99" .67" +248°F +347°F NCB306SS 2.84" 1.18" .75" +248°F +347°F NCB306SSL (Mack) 2.84" 1.18" .75" +248°F +347°F Viton NCB306VV* 2.84" 1.18" .75" +419°F +400°F RT Series (K-2468) MC MIK1 MaxHD - Viton high temp pilot bearing, MC HB200 hinged clutch brake PA1EF66030 Nitrile pilot bearing, 127760 1 piece clutch brake FR Series (K-3600) MC MIK3 MaxHD - New design input shaft, Viton high temp pilot bearing, MC HB200 hinged clutch brake PA1900172 New design input shaft, Nitrile pilot bearing, 127760 1 piece clutch brake FR Series (K-3602) MC MIK8 MaxHD - Original design input shaft, Viton high temp pilot bearing, HB200 hinged clutch brake FR Hydraulic Release (K-4124) MW1K4124 New design input shaft, Viton high temp pilot bearing, 127760 1 piece clutch brake Rockwell Meritor RM, RMO, RMX, G MW1KIT 20088 Meritor input shaft, Viton high temp pilot bearing, 127760 1 piece clutch brake OIL SEAL KIT PA1EF69520 INPUT SHAFT ASSEMBLY PA1EF67490 10,13,15,18 Speed Hinged *Minimum Eaton Clutch Division: The operating temperature that the pilot bearing sees has increased in the last several years. This creates operating conditions that are no longer acceptable to the standard pilot bearings and grease. In addition, the life of the clutch has increased. The use of high temperature grease and Viton seals are now mandatory to ensure adequate bearing life. Pilot bearing failure usually results in a warranty claim for drag or clutch noise. This results in a claim against Eaton Clutch. CLUTCH BRAKES MC HB200 Hinged Clutch Brake 2" x .375" Thick - Tooth Style MC HB200-440 Hinged Clutch Brake 2" x .44" Thick - Tooth Style MC HB200-500 Hinged Clutch Brake 2" x .5" Thick - Tooth Style MC HB175 Hinged Clutch Brake 1" Tooth Style MD BK312 Hinged Clutch Brake 1.75" Button Style MD BK313 Hinged Clutch Brake 2" Button Style MC AHB200 Multi-Piece Hinged Clutch Brake 2" x .375" Thick Button Style 2-Piece MC M175 2 pc. Babcock Split Clutch Brake 1.75" MC M200 2 pc. Babcock Split Clutch Brake 2" MC 127200 2 pc. Split Brake 2" Roll Pin 1-Piece MC 127740X 1 pc. Torque Limiting Brake 1.75" MC 127760X 1 pc. Torque Limiting Clutch Brake 2" MC 125C-40 1.75” x .125” Thick MC 125C-41 2” x .125” Thick CLUTCH INSTALLATION KITS CLUTCH FORK MW1105C-137 HYDRAULIC CLUTCH RELEASE FORK AUT755.CF102H Ref. A7786 DRIVE LUGS MC 274C-6 Drive Pin CLUTCH ADJUSTER MC 125489 Kwik Adjuster CROSS SHAFTS MW1106C1185R 5.76" Short Shaft MW1106C1498R 6.50" Short Shaft BELL HOUSE BUSHING MW112815 CLUTCH BRAKE WASHERS PILOT BEARINGS Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 11Clutch Guide New We Resurface Flywheels in DM • DV • KC TOOLS OT 5044 Clutch Self-Adjusting Rotator Tool – 3/4” MC MAXCAT1 Clutch Adjustment Tool MC GT1 Bushing Grease Tool - Clutch CLUTCH ALIGNING SHAFTS MISCELLANEOUS TOOLS CLUTCH HANDLER - LOW CLEARANCE OT 5018A Flywheel Handling Attachment for Clutch Handler #5018 516160 CLUTCH ADJUSTING WRENCH OT 7028 CLUTCH ADJUSTMENT GAUGE SET OT 5035 TRANSMISSION OUTPUT SHAFT END YOKE REMOVER OT 7075 TRANSMISSION JACK OT 5019A NEW FLYWHEELS *Not recommended to turn the flywheel, always replace the flywheel as a best practice. Bold Part Numbers are Stocking Flywheels, non-stocking units available within 24-48 hours Flywheel Gauge P/N MC FG1 P/N OEM # Application Description Bore Dia. Pilot Mounting CAT MW1WA1265875 1265875 C7/3116/3126 Flat 134 tooth 13" OR 14" CLU 8BLT 1 DOWEL 17OD 134 7" 206 / 305 8 Bolt Holes & 1 Dowel MW1WA2569653 2569653 C15, C16, C18, 3406, 3406E Flat 113 tooth 15" CLUTCH FLAT 10" OPEN 20OD 113T 10.12" 306 12 Bolt Holes MW1WA4P8515 4P8515 C9/ C10 /C11/ C12 /C13 / 3176 Flat 113 tooth 15" CLU 10"OP 8BLT 1DOWL 20OD 113T 10" 306 8 Bolt Holes MW1WA9Y9311 9Y9311 3208 Flat 134 tooth 14" CLU 7.12"OP 10 OFST BLT 17" 134 7.12" 206 / 305 10 Offset Bolt Holes MW1WA901-10-4112 4P4797 3406/3406E/C15 Flat 113 tooth 10" OP 15" OD 113T 10" 306 12 Bolt Holes CUMMINS MW1WA3016495 3016495 NT855 Pot 103 Tooth 14" CLU CUP 6BLT 17"OD-103T 8.37" 306 6 Bolt Holes & 2 Threaded MW1WA3042787 3042787 L10 / M11 Pot 103 tooth 14" CLU CUP 8BLT 2 THRD 17"OD-103T 7.25" 306 6 Bolt Holes & 2 Threaded MW1WA902-110-4130 3071535 N14 / NT855 Flat 103 tooth 15" CLU FLAT 6BLT 2 THR 17"OD-103T 10.12" 306 6 Bolt Holes & 2 Threaded MW1WA3071615 3071615 L10 / M11 Flat 103 tooth 15" CLU FLAT 8BLT 2 THR 17"OD-103T 10.12" 306 8 Bolt Holes & 2 Threaded MW1WA3680922 3680922, 3680921 ISX, Signature 600 Flat 113 tooth 15" CLU FLT 10" 12BLT 20" OD 113T 10" 306 12 Bolt Holes MW1WA3906807 3906807 8.3L C-Series Flat 173 tooth 14" CLU FLT 8BLT 2 THR 17"173T .54" 7.25" 206 / 305 8 Bolt Holes & 2 Threaded MW1WA3921263 3921263 5.9L B Series Flat 173 tooth 14" CLU FLT 8BLT 17" OD -138T .610" 7.25" 306 8 Bolt Holes MW1WA3922645 3922645 8.3L C Series Flat 138 tooth 14" CLU FLT 8BLT 17" OD -138T .875" 7.25" 206 / 305 8 Bolt Holes DETROIT MW1WA23514177 23514177 Light Weight - 60 Series Flat 118 tooth 10" bore 15" CLUTCH 20"OD-118T Light Weight 10" 306 12 Bolt Holes MC 23509709 23509709 60 Series Flat 118 tooth 10" bore 15” CLUTCH 20”OD-118T Standard 10" 306 12 Bolt Holes FORD MW1WAE7HZ6375A E7HZ6375A 6.6L / 7.8L Diesel Flat 138 tooth 14" CLUTCH FLAT 8BLT 17" OD 138T 7.50" 206 / 305 8 Bolt Holes MACK/ VOLVO MW1WA530GB3145BM 530GB3145BM E7 Flat w/timing marks 118 tooth 15X9 10"& TIM MK 6B &1DP 20" 118T 10" 306 6 Bolt Holes & 1 Dowel MW1WA530GB3170M 530GB3170M E7 E-Tech Flat 117 tooth 2 notched 15X9 10"& TIM MK 6B &1DP 20" 117T 10" 306 6 Bolt Holes & 1 Dowel MW1WA20730056 20730056 VED12 Flat 153 tooth 15" CLU 14BLT & 1 DP 19.5" OD 153T 10" 306 14 Bolt Holes & 1 Dowel MW1WA905-10-4168 21184666 ISHIFT VOLVO D13/ MDRIVE MACK MP8 Automatic Transmission 10” Bore 153 Tooth 10" - 14 Crank Mounting Bolts, 12 Clutch mounting bolts NAVISTAR MW1WA1809144C91 1809144C91 6.9L / 7.3L Flat 137 tooth 13" OR 14" CLUTCH 9BLT 17" OD -137T 7.25" 205 9 Bolt Holes MW1WA1810855C93* 1810855C93 DT466 A-B-C- Flat 138 tooth (1975-1996) 14" CLUTCH 8BLT 17"OD -138T 7.25" 205 8 Bolt Holes MW1WA1818214C91 1818214C91 7.3L / 444E Flat 137 tooth 13" OR 14" CLU 10BLT 17" OD 137T 7.25" 206 / 305 10 Bolt Holes MW1WA1821915C91* 1821915C91 DT466E Flat 138 tooth 14" CLUTCH 12BLT 17"OD 138T 7.25" 0 12 Bolt Holes MC AT175X1 1 3/4” OD, 1” Pilot MC AT-200-10 2” OD, 1 1/4” Pilot, 10 Splines, 7.3” Long MC AT-200-14 14 Spline MC AT-200-18 18 Spline MC AT-200-24 24 Spline MC AT175 1 3/4” OD, 1 1/4” Pilot, Spline 7.375” Long Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 11Clutch Guide New 6 Eaton Differentials Tandem Front Ref. # Single or Tandem Rear Ref. # GENDSP40-336 GENDS404-336 GENRSP40-336 GENRS404-336 GENDSP40-355 GENDS404-355 GENRSP40-355 GENRS404-355 GENDSP40-370 GENDS404-370 GENRSP40-370 GENRS404-370 GENDSP40-390 GENDS404-390 GENRSP40-390 GENRS404-390 Bold Part Numbers are Stocking Units I-Shift Transmissions Part # Description Max Torque Gears Generation Application GENAT2512C Automatic Transmission 2500 12 III AND IV Standard GENATO2512C Automatic Transmission w/ Overdrive 2500 12 III AND IV Standard GENAT2612D Automatic Transmission 2600 12 V AND EEV Standard GENATO2612D Automatic Transmission w/ Overdrive 2600 12 V AND EEV Standard GENAT2612D-HD Automatic Transmission 2600 12 V AND EEV Heavy Duty GENATO2612D-HD Automatic Transmission w/ Overdrive 2600 12 V AND EEV Heavy Duty GENATO3112C Automatic Transmission w/ Overdrive 3100 12 III AND IV Standard GENATO3112D Automatic Transmission w/ Overdrive 3100 12 V AND EEV Standard GENATO3112D-HD Automatic Transmission w/ Overdrive 3100 12 V AND EEV Heavy Duty Rockwell Differentials Tandem Front Single or Tandem Rear GENRD20145-342 GENRR20145-342 GENRD20145-358 GENRR20145-358 GENRD20145-373 GENRR20145-373 GENRD20145-390 GENRR20145-390 Eaton-Fuller Transmissions Part # Description GENFRO16210CP 10 Speed GENRTLO16713AP 13 Speed GENRTLO18913AH 13 Speed GENRTLO18718BP 18 Speed GENRTLO18918BH 18 Speed GENRTO16908LLP 8 Speed Plus 2 Deep Reduction Speeds If part number ends with: H - Halo Installed (plug kits included) P - Pump Installed - ready for external cooler HD4560 Allison Transmission HD3500 Allison Transmission Factory Authorized Remanufacturer 36 Month/Unlimited Miles Warranty Bold Part Numbers are Stocking Units Phone 773-247-6900 | Fax 773-247-2632 ur remanufactured rkmanship for the plication. e, at General Truck nt. Any component e original warranty administered only You must contact 1 for authorization gible for warranty urred as a result of oper application or mponents that may s, etc… arts, Inc. and shall e conditions stated y failed component replacement. Any s, Inc. and may be ned to be a non- REMAN UNITS IONS ipment is ssions and rebuilt and none. We test our state-of- ion mechanics ndustry. ALS ipment is the differential expert for ustrial, agricultural, construction, mining ks and equipment. General Truck Parts and and medium duty differentials and parts. ual Transmissions rentials 4040 W. 40th Street | Chicago, IL 60632 | www.GeneralTruckParts.com | Toll Free 800-621-3914 | Phone 773-247-6900 | Fax 773-247-2632 This warranty covers parts and labor to repair or replace, at General Truck Parts, Inc.’s option, the failed remanufactured component. Any component repaired or replaced will retain the remainder of the original warranty period. General Truck Parts, Inc. nationwide warranty may be administered only by one of our approved warranty repair facilities. You must contact General Truck Parts, Inc. at 1-800-621-3914 Ext. 2581 for authorization prior to any repairs being made in order to be eligible for warranty coverage. This warranty shall not extend to failures or damage incurred as a result of improper installation, improper lubrication, abuse, improper application or improperly installed accessories or other attached components that may be worn or failed, i.e. drive shafts, yokes, power takeoffs, etc… All warranty claims shall be made to General Truck Parts, Inc. and shall be supported by satisfactory evidence in respect of the conditions stated herein. General Truck Parts, Inc. reserves the right to have any failed component returned to our facility for inspection prior to repair or replacement. Any freight incurred will be prepaid by General Truck Parts, Inc. and may be billed back to your account if the failure is determined to be a non- warrantable failure. a supplier of manual transmissions and transfer case products, both rebuilt and new. Our quality is second to none. We test all rebuilt transmissions on our state-of- the-art dynonometer. Our union mechanics are some of the best in the industry. DIFFERENTIALS General Truck Parts and Equipment is the differential expert for on-highway, off-highway, industrial, agricultural, construction, mining and logging heavy duty trucks and equipment. General Truck Parts and Equipment also carries light and medium duty differentials and parts. 2 Year Warranty — Manual Transmissions 1 Year Warranty — Differentials OE QUALITY TRANSMISSIONS & DIFFERENTIALS WARRANTY Manual & Automated Manual Transmissions: 36 Months/Unlimited Miles Differentials: 36 Months/Unlimited Miles Transfer Cases: 6 Months/Unlimited Miles Off highway/Hydraulic Components: 6 Months/ Unlimited Miles SAME DAY OR NEXT DAY SHIPPING With an extensive inventory on-hand and ready to ship, most orders will be shipped the day of order if the order is received before 12 Noon (CST). Orders received after 12 Noon (CST) will be processed and shipped the following business day. (Note: This applies to common products. Specialty items may have longer lead times). Midwest Wheel is your Heavy Duty Drivetrain Supplier Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 11Clutch Guide New 7 GEAR OIL FOR TRAILER HUBS SH 550032647 5 Gallon SH 550045337 1 Gallon SH 550032968 55 Gallon Special Order Shell Spirax ® S6 ATF A295 For Allison Automatic Transmissions. Premium Synthetic Technology Multi-Vehicle Automatic Transmission Fluid. Spirax ® S6 GME 40 Eaton approved synthetic transmission fluid for manual Fuller Transmissions. Shell Spirax ® S6 AXRME 75W-90 Synthetic, long life axle and manual transmission oil. Recommended for use in all rear axles. SH 550026915 5 Gallon SH 550026914 16 Gallon SH 550026918 55 Gallon Special Order SH 550044797 5 Gallon SH 550044799 16 Gallon SH 550044796 55 Gallon Special Order LUCLUC10043 qt 85/140 plus LUCLUC10066 5 gallon 80/90 LUCLUC10072 5 gallon 75W/90 Synthetic LUBRICANTS Input Yoke Yoke P/N Strap Kit Input Nut Input Seal 1710 Full Round SD16-4-9031X - MW1127589 MW1127591 1710 Half Round SD16-4-9031-1X SD16.5-718X SPL170 Half Round SD1170-4-261-1X SD1170-70-18X SPL90 Half Round SD190-4-251-1X SD190-70-28X Breather Kit: H6 507162 GENRSP40-XXX, RD404-XXX Eaton Rear Rear End Breather Kit: H6 507162 Input Yoke Yoke P/N Strap Kit Input Nut Input Seal 1710 Half Round SD16-4-6391-1X SD16.5-70-18X MW140X1237 RI A11205Z2730 GENRR20145-XXX Meritor Rear Rear End Breather Kit: H6 507162 Input Yoke Yoke P/N Strap Kit Input Nut Input Seal 1810 Half Round SD16.5-4-3381-1X SD16.5-70-18X MW140X1233 RI A11205X2728 1810 Full Round SD16.5-4-3381X - 1760 Half Round SD16.3-4-331-1X SD16.5-70-18X Output Yoke Yoke P/N Output Nut Output Seal 1710 Half Round SD16-4-6371-1 MW140X1237 R1 A11205Y2729 SPL170 Half Round SD1170-4-741-1X GENRD20145-XXX Meritor Front Rear End Output Yoke Yoke P/N Output Nut Output Seal 1710 Half Round SD16-4-9231-1X - H6 K2918 1760 Half Round SD16.3-4-161-1X 1760 Full Round SD16.3-4-1681 1810 Half Round SD16.5-4-4631-1X 1810 Full Round SD16.5-4-4631 SPL250 Half Round SD1250-4-271-1X Eaton/Fuller Transmissions All w/10 Spline Shaft Input Yoke Yoke P/N Strap Kit Input Nut Input Seal 1810 Full Round SD16.5-4-4571X - MW1128049 MW1127591 1810 Half Round SD16.5-4-4571-1X SD16.5-70-18X 1760 Full Round SD16.3-4-5221X - 1760 Half Round SD16.3-4-5221-1X SD16.5-70-18X SPL170 Half Round SD1170-4-201-1X SD1170-70-18X SPL250 Half Round SD1250-4-81-1X SD1250-70-18X Output Yoke Yoke P/N Output Nut Output Seal 1710 Full Round SD16-4-9041X MW1127588 MW1127592 1710 Half Round SD16-4-9041-1X SPL170 Half Round SD1170-4-221-1X GENDSP40-XXX, DD404-XXX Eaton Front Rear End Breather Kit: H6 507162 SENTINEL ESP FILTERED VENT ST 359-6137 Drive Axle Vent (3/8” adapter) Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

11Automated Manual Transmission Clutches130005132021 CATALOG NUMBER 11 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ UltraShift PLUS ECA (Electronic Controlled Actuator) MC MAX121000X 2”-10 Spine 1750ft/lb MC MAX122002X 2”-14 Spine 1850ft/lb AUTOMATED MANUAL TRANSMISSION CLUTCHES *New inertia brake may be required P/N GP K3637 *Eaton software required to remove and install unit *New flywheel required for every install *Eaton software required to remove and install unit ALL NEW, NO CORE Made in USA Detroit D12 Transmission Part Number OE Reference Description Alignment tool MC ANK4489CL K-4489 (Eaton) Single-Plate, 18 Involute Spline, Organic / 6-Spring / 1850 Torque Detroit D12 MC AT-200-18 Volvo I-Shift / Mack mDrive Part Number OE Reference Description Alignment tool MC MAX104461-1 104461-1 (Eaton) 3400 700 359 (Sachs) Single-Plate, 24 Involute Spline, Organic / 6-Spring / 1850 Torque (13L Engine,Volvo I-Shift and Mack mDrive) MC AT-200-24 MC A-1001 - Clutch Actuator for MC MAX104461-1 - 430mm x 50mm Stamped Steel Clutch At the front of the UltraShift 6, 10 and 13-speed transmissions is the UltraShift DM clutch, which engages and disengages without an in-cab pedal. The AutoClutch uses a traditional two- plate configuration for heavy duty and single-plate for medium duty, complete with soft rate dampers and ceramic facings for smooth engagement. This clutch system offers the durability and performance necessary to withstand the high actuation conditions and associated with automated transmission systems. This clutch has been developed for a wide range of customer applications from Linehaul to Vocational to meet with the many specific automated transmissions offered by Eaton. UltraShift ™ DM Clutch Eliminates the need for a clutch pedal and helps to maximize clutch life. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Prestone TSB for Training130009252017 CATALOG NUMBER 10 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Technical Service Bulletin PCTSB-2017-01 There are four basic heavy duty coolant formulation technologies: • Inorganic Additive technology • Hybrid Organic Acid Technology • Nitrite Organic Acid Technology • Nitrite Free Organic Acid Technology There are other coolant technologies but they pertain to Automotive Light and Medium Duty vehicles. Inorganic Additive Technology Coolant (IAT): Known as HD Conventional green; other colors are used as well. This is a low silicate formulation which may include Phosphate and/or borate, nitrate, nitrite, azoles, and other inorganic compounds. This type of coolant formulation is not used today in factory fill. When used in a HD application during a complete fill SCA must be added to bring inhibitor levels up to proper protection. The HD technician must monitor and recharge the coolant, when necessary, for proper protection. The optimum change interval for this type of coolant is 3000 hours, 1 year, or 100,000 to 150,000 miles. The change interval would be based on the OE manufacturer recommended preventative maintenance schedule. HD Extended Service Interval Coolant (IAT): This is also an inorganic additive technology coolant known as an ESI type coolant. This formulation may still be used for factory fill in some heavy duty cooling systems. When following TMC recommend practices the color should be purple, pink or blue, but other colors are used as well. This is a low silicate formulation which may include Phosphate and/or borate, nitrate, nitrite, azoles and other inorganic compounds. ESI coolants are pre-charged with the acceptable levels of inhibitors and SCAs do not need to be added at initial fill or after a proper flush and fill. Supplemental Coolant Additives must be monitored and recharged when necessary. It is recommended that ESI coolants have a lab analysis completed at least once a year to monitor ethylene glycol condition and for contaminates, such as, metals, corrosion by-products, and outside contaminates. Lab analysis can be used to determine coolant condition and change interval. Hybrid Organic Acid Technology Coolant (HOAT): This type of coolant is typically not used as heavy duty factory fill in the United States. HOAT coolants typically utilize a combination of organic acids and inorganic additives, such as, low silicate, nitrite and nitrate in the inhibitor package. HOAT coolant comes in multiple colors depending on the coolant manufacturer but are typically red and yellow. Following TMC Recommended Practice: RP-365 - Coolant Maintenance Guidelines preventative maintenance on a HOAT coolant is typically performed on an interval of 25,000 miles or as specified by the engine manufacturer, similar to an HD IAT coolant. Heavy Duty Coolant Technologies Overview Technical Service Bulletin Page 1 PCTSB-2017-01 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation There are four basic heavy duty coolant formulation technologies: • Inorganic Additive technology • Hybrid Organic Acid Technology • Nitrite Organic Acid Technology • Nitrite Free Organic Acid Technology There are other coolant technologies but they pertain to Automotive Light and Medium Duty vehicles. Inorganic Additive Technology Coolant (IAT): Known as HD Conventional green; other colors are used as well. This is a low silicate formulation which may include Phosphate and/or borate, nitrate, nitrite, azoles, and other inorganic compounds. This type of coolant formulation is not used today in factory fill. When used in a HD application during a complete fill SCA must be added to bring inhibitor levels up to proper protection. The HD technician must monitor and recharge the coolant, when necessary, for proper protection. The optimum change interval for this type of coolant is 3000 hours, 1 year, or 100,000 to 150,000 miles. The change interval would be based on the OE manufacturer recommended preventative maintenance schedule. HD Extended Service Interval Coolant (IAT): This is also an inorganic additive technology coolant known as an ESI type coolant. This formulation may still be used for factory fill in some heavy duty cooling systems. When following TMC recommend practices the color should be purple, pink or blue, but other colors are used as well. This is a low silicate formulation which may include Phosphate and/or b rate, nitrate, nitrite, azoles and other inorganic compounds. ESI coolants are pre-charged with the acceptable levels of inhibitors and SCAs do not need to be added at initial fill r aft r a proper flush and fill. Supplemental Coolant Additives must be monitored and recharged when necessary. It is recommended that ESI coolants have a lab analysis completed at least once a year to monitor ethylene glycol condition and for co aminates, such as, metals, corrosion by-products, and outside contaminates. Lab analys can be used to determine coolant conditio a d change interval. Hybrid Orga ic Acid Technology Coolant (HOAT): Thi type of coolant is typically not used as heavy duty factory fill in the United States. HOAT coolants typically utilize a combination of organic acids and inorganic additiv s, such as, low silica e, nitrite d nitrate in the inhibitor package. HOAT coolant comes in multiple col rs depending on the c olant manufactur r but are typically red and yell w. Following TMC Recommended Practice: RP-365 - Coolant Maintenance Guidelines preventative maintenance on a HOAT coolant is typically performed on an interval of 25,000 miles or as specified by the engine manufacturer, similar to an HD IAT coolant. Heavy Duty Coolant Technologies Overview There are four basic heavy duty coolant formulation technologi s: • • Inorganic Additive technology • • Hybrid Organic Acid Technology • • Nitrite Organic Acid Technology • • Nitrite Free Organic Acid Techn logy There are oth r coolant technologi s bu they pertain to Automotive Light and Medium Duty vehicles. Inorganic Additive Technology Coolant (IAT): Known as HD Conventional gree ; other colors are used as well. This is a low silicate formulation which may include Phosphate and/or borate, nitrate, nitrite, azoles, and other inorganic compounds. This type of coolant formulation is not used today in factory fill. When used in a HD application during a complete fill SCA must be added to bring inhibitor levels up to proper protection. The HD technician must monitor an recharge the c olant, when necessary, for proper protection. The optimum change interval for this type o coolant is 3000 hour , 1 year, or 100,000 to 150,000 miles. The ch nge interval w uld be bas d on the OE manufacturer recom- mended preventative maintenance schedule. HD Exten ed Service Interv l Coolant (IAT): This is also an norganic additiv technology coolant k own as an ESI type coolant. This formulation may still be used for factory fill in some heavy duty cooling systems. When following TMC recommend practice the color should be pu ple, pink or blue, but other colors are used as well. This is low silicate formulation which may include Phosphate and/or borat , nitrat , nitrite, azoles and other inorganic compounds. ESI olants are pre-charged with the acceptable levels of inhibitors and SCAs do not need to b dd d at initial fill or after a proper flush a fill. Supplement l Coolant Additiv s ust be monit red and recharged w e n cessa y. It is recommended that ESI coolants have a l b analysis complet d at least once a year to monitor ethylene glycol condition and for contaminates, such as, metals, c rr sion by-products, and outside contaminates. Lab analysis can be used to determine coolant condition and cha ge interval. Hybrid Organic Acid Technology Co lant (HOAT): This type of coolant is typically not used as heavy duty fa tory fill in the United States. HOAT coolants typically util ze a combination of organic acids and inorganic additives, such as, low silicate, nitrite and nitrate in the inh bitor packag . HOAT coolant comes in multiple colors depending on the coolant manufacturer but are typically red and yellow. Following TMC Recommended Pr ctice: RP-365 - Coolant Maintenance Guid lines preventativ maintenance on a HOAT coola t is typically performed o an interv l of 25,000 miles or as specified by the engine manufacturer, similar to an HD IAT coolant. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Technical Service Bulletin Page 2 PCTSB-2017-01 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation Nitrite Organic Acid Technology Coolant (NOAT): This coolant does not contain inorganic inhibitors, such as, silicate or borate. It is an organic inhibitor base with nitrite and, potentially, molybdate for extra cavitation pitting control. NOAT coolant is known as an Extended Life Coolant or HD ELC. NOAT coolants have been very common in factory fill applications, but many OEMs are now transitioning to HD Nitrite Free OAT coolant. NOAT coolants protect the cooling system much longer and with less maintenance than Conventional (IAT) coolants. There is no need to monitor SCA or install SCA charged coolant filters. TMC recommended practice color is Red, but other colors are used as well. NOAT type coolant protects HD cooling system components up to 6000 hours or 300,000 miles. You can extend this protection by adding an Extender at 6000 hours or 300,000 mile interval. This gives a protection up to 12,000 hours or 600,000 miles. A lab analysis is recommended before adding the Extender. This analysis allows the technician to decide, to add an Extender, or flush and fill the system with new coolant. Do not use a charged coolant filter with NOAT HD ELC coolant. Nitrite Free Organic Acid Technology Coolant (NF OAT): This coolant is known as HD Nitrite Free Extended Life Coolant or HD NF ELC and it uses organic inhibitors and, potentially, molybdate and/or nitrate. This coolant uses organic inhibitors, molybdate and/or nitrate to help control corrosion and cavitation erosion in a cooling system. It does not contain inorganic inhibitors, such as, Silicate, Nitrite, and Borate. There is no need to monitor SCA and do not install a SCA charged coolant filter. HD NF OAT coolant is used in some HD vehicles for factory fill. The color is typically yellow, red, or blue but other colors may be used as well. HD NF OAT coolant protects the cooling system for up to 12,000 hours or 600,000 miles. No Extender is needed, but it is recommended to test the coolant at least twice a year with organic inhibitor test strips to test organic inhibitors, pH, and freeze point levels. It is also recommended to have a lab analysis completed at 6,000 hours or 300,000 miles to check the condition and contaminate levels of the coolant. Heavy Duty Coolant Technologies Overview (continued) It is not recommend to use an IAT or NOAT type coolant to top-off HD NF OAT coolant. If coolant is mixed it should not exceed 25% capacity. Follow recommended test procedures to determine if the cooling system needs to be flushed and refilled. It is also not recommended to use a HD NF OAT type coolant to top-off a HD IAT type coolant. It is acceptable with some manufacturers to top-off a HD NOAT type coolant with a HD NF OAT coolant. Always consult the OE Manufacturers recommended cooling system maintenance practices. Recommended Practice For Topping Off A HD Cooling System Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser Part Number: HD100 Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Technical Service Bulletin Page 3 PCTSB-2017-01 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation HD Cooling System Antifreeze/Coolant Label Location and Identification To locate the antifreeze/coolant label on a HD cooling system visually inspect the areas listed below: • Radiator near the radiator cap. • Side tanks of the radiator near the top. The label would most likely be located on the passenger’s side of the radiator. • On the surge tank (cooling system reservoir tank) Below are a few examples of labels. Compatibility chart is located on Page 12. Fully Formulated Heavy Duty Coolant colors may be: • Purple • Pink • Blue (Cummins) • Green (Sold in Canada) Top-off with Prestone Command ® Heavy Duty Extended Service Interval Antifreeze/Coolant - Purple OR Flush and Refill with Prestone Command ® HD Nitrite Free Extended Life Antifreeze/Coolant NOAT Heavy Duty Extended Life Coolant color may be: • Red (most widely used color) • Other colors may be used, but it will state HD ELC coolant on label Important: Read label carefully. NOAT ELC coolant label will not state Nitrite Free OAT. Top-off with Prestone Command ® HD Extended Life Antifreeze/Coolant - Red or Prestone Command ® HD Nitrite Free Extended Life Antifreeze/ Coolant - Yellow OR Flush and Refill with Prestone Command ® HD Nitrite Free Extended Life Antifreeze/Coolant OAT Nitrite Free Heavy Duty Extended Life Coolant color may be: • Red (most widely used color for over-the-road Tractors) • Yellow or Blue (some over-the-road, construction, and ag equipment) • Important: Read label carefully. Label with Nitrite Free OAT ELC coolant will state Nitrite Free OAT. Top-off with Prestone Command ® HD Nitrite Free Extended Life Antifreeze/Coolant - Yellow OR Flush and Refill with Prestone Command ® HD Nitrite Free Extended Life Antifreeze/Coolant Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Technical Service Bulletin Page 4 PCTSB-2017-01 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation Conversion from an IAT type HD coolant to Prestone Command ® HD NF Extended Life Antifreeze/Coolant: (Never open a hot cooling system, wait for the cooling system to cool down before opening) This conversion may be done any time, at the fleet’s discretion. Remove any SCA release filters first and completely flush the cooling system with water two to three times to remove the IAT type coolant. If the cooling system shows signs of contamination utilize Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser during the process and flush the cooling system with water to remove the chemical flush cleaner and contaminates. It is preferred (if equipped) to unscrew and remove all of the engine cooling system drain plugs (including block drains) to completely drain all flush water from the cooling system. An engine could hold, up to, 15% - 25% of contaminated coolant or flush water. The next few pages describe recommended testing procedures to determine if the cooling system needs maintenance or if a conversion is recommended from an IAT type coolant to Prestone Command ® HD NF Extended Life Antifreeze/Coolant. HD Coolant Conversion Notes: Recommended HD Coolant Test Equipment, Water Analysis & HD Coolant Test Strips AFC200 Refractometer Accurately test Freeze Point & DEF Concentration Part# AFC220 HD IAT Coolant Test Strips Measures: Nitrite, % Glycol, & pH Part# AFC240 HD OAT ELC Coolant Test Strips Measures: % Glycol, % OAT Inhibitor, Nitrite, & pH Part# AFC210 Water Quality Test Strips Measures: Hardness, pH & Chloride Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Page 5 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation Technical Service Bulletin PCTSB-2017-01 Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Page 6 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation Technical Service Bulletin PCTSB-2017-01 Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Technical Service Bulletin Page 7 PCTSB-2017-01 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation Use test results from pages 5 & 6 to make determinations (see below) “Making Determinations” ONLY APPLY to CONVENTIONAL IAT COOLANTS • It is not recommended to add current NOAT or NF OAT coolants to a conventional IAT fluid. • Make all fluid determinations before making concentration or level adjustments. NOTE: When using test strips follow the test instructions on the test strip card or bottle. (When using Prestone test strips it is advisable to use the color standards on the cards) Warning: Do not open the cooling system if engine is hot! Wear gloves, if skin contacts fluid wash immediately. TEST INSTRUCTIONS Collect coolant sample from the radiator or petcock at room temperature. Remove a strip from the bottle (do not touch pads on strip). Dip the strip in coolant sample for 2 seconds. Remove and shake strip briskly to remove excess liquid. Hold strip level and wait 20 seconds, then match Freeze Point and pH to color chart. After 1 minute, match Nitrite to color chart. Prestone Command test strip AFC220 should only be used for purple IAT/ESI fully formulated HD coolants. Making Determinations: 1. If the pH level is below 8.0: • Remove any SCA filters and flush the cooling system with water and fill with new coolant, preferably Prestone Command ® HD NF Extended Life Antifreeze/Coolant. • If the cooling system shows visible signs of contamination flush the system with Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser, then flush with water to remove chemical flush solvent and refill with Prestone Command ® HD NF Extended Life Antifreeze/Coolant. 2. If the pH level is between 8.0 – 11.0 and the nitrite level is between 1200 and 3000: • The fluid is OK. • If needed top off with Prestone Command ® HD Extended Service Interval Antifreeze/Coolant or water to adjust the level and concentration. 3. If the pH level is between 8.0 – 11.0 and the nitrite level is below 1200: • Remove any SCA filters and flush the cooling system with water and refill with new Prestone Command ® HD NF Extended Life Antifreeze/Coolant. • If the cooling system shows visible signs of contamination flush the system with Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser, then flush with water to remove chemical flush solvent and refill with Prestone Command ® HD NF Extended Life Antifreeze/Coolant. 4. If the pH level is above 11.0: • Remove any SCA filters and flush the cooling system with water and fill with new coolant, preferably with Prestone Command ® HD NF Extended Life Antifreeze/Coolant. • If the cooling system shows visible signs of contamination flush the system with Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser, then flush with water to remove chemical flush solvent and refill with Prestone Command ® HD NF Extended Life Antifreeze/Coolant. When utilizing Test Strips do not use the above color chart. Use the color chart on the Test Strip Bottle or individual card. HD Conventional Coolant (IAT) Testing Fluid Conversion/Maintenance Plan Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Technical Service Bulletin Page 8 PCTSB-2017-01 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation Use test results from pages 5 & 6 to make determinations (see below) “Making Determinations” ONLY APPLY to HD Extended Life COOLANT (NOAT) • Never use SCA filters with current HD Extended Life Coolant (NOAT). • Make all fluid determinations before making concentration or level adjustments. NOTE: When using test strips follow test instructions on the test strip card or bottle. (When using Prestone test strips it is advisable to use the color standards on the cards) Warning: Do not open the cooling system if engine is hot! Wear gloves, if skin contacts fluid wash immediately. TEST INSTRUCTIONS Collect coolant sample from the radiator or petcock at room temperature. Remove a test strip from the bottle. DO NOT touch the pads at the end of the strip. Dip the strip in coolant sample for 2 seconds. Remove and shake strip briskly to remove excess liquid. Wait 45 seconds, then match to the RED numbers on the color chart. Complete color matching within 20 seconds. Prestone Command test strip AFC240 should only be used for red or yellow NOAT or NF OAT HD coolants. Making Determinations: 1. If the pH level is below 7.0: • Full fluid analyses are required, or flush the cooling system with water and refill with new Prestone Command ® HD Extended Life Antifreeze/Coolant or Prestone Command ® HD NF Extended Life Antifreeze/Coolant. • If the cooling system shows visible signs of contamination flush the system with Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser , then flush with water to remove chemical flush solvent and refill with Prestone Command ® HD Extended Life Antifreeze/Coolant or Prestone Command ® HD NF Extended Life Antifreeze/Coolant. 2. If the pH level is between 7.0 - 10.0 and the nitrite level is between 500 - 800: • The coolant is OK. • If needed top off with the correct amount of Prestone Command ® HD Extended Life Antifreeze/Coolant or water to adjust the level and concentration. 3. If the pH level is between 7.0 – 10.0 and the nitrite level is above 800: • Flush the cooling system with water and refill with new Prestone Command ® HD Extended Life Antifreeze/Coolant or Prestone Command ® HD NF Extended Life Antifreeze/Coolant. • If the cooling system shows visible signs of contamination flush the system with Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser, then flush with water to remove chemical flush solvent and refill with Prestone Command ® HD Extended Life Antifreeze/Coolant or Prestone Command ® HD NF Extended Life Antifreeze/ Coolant. 4. If the pH level is above 10: • Flush the cooling system with water and refill with new Prestone Command ® HD Extended Life Antifreeze/Coolant or Prestone Command ® HD NF Extended Life Antifreeze/Coolant. • If the cooling system shows visible signs of contamination flush the system with Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser, then flush with water to remove chemical flush solvent and refill with Prestone Command ® HD Extended Life Antifreeze/Coolant or Prestone Command ® HD NF Extended Life Antifreeze/ Coolant. Part # AFC240 test strips are for Organic Acid Coolants ONLY, NOT for use with convention silicate (IAT) or hybrid organic acid coolants (HOAT). When utilizing Test Strips do not use the above color chart. Use the color chart on the Test Strip Bottle or individual card. HD EXTENDED LIFE COOLANT (NOAT) Testing Fluid Conversion/Maintenance Plan Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Technical Service Bulletin Page 9 PCTSB-2017-01 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation Use test results from pages 5 & 6 to make determinations. (see below) “Making Determinations” ONLY APPLY to HD NF Extended Life COOLANT (NF OAT). Confirm HD NF OAT color could be RED or YELLOW. • Never use SCA filters with current HD NF Extended Life Coolant (NF OAT). • Make all fluid determinations before making concentration or level adjustments. NOTE: When using test strips follow test instructions on the test strip card or bottle. (When using Prestone test strips it is advisable to use the color standards on the cards) Warning: Do not open the cooling system if engine is hot! Wear gloves, if skin contacts fluid wash immediately. TEST INSTRUCTIONS Collect coolant sample from the radiator or petcock at room temperature. Remove a test strip from the bottle. DO NOT touch the pads at the end of the strip. Dip the strip in coolant sample for 2 seconds. Remove and shake strip briskly to remove excess liquid. Wait 45 seconds, then match to the BLACK numbers on the color chart if the coolant color is YELLOW or match to the RED numbers on the color chart if the coolant color is RED. Complete color matching within 20 seconds. Prestone Command test strip AFC240 should only be used for red or yellow NOAT or NF OAT HD coolants. Making Determinations: 1. If the pH level is below 7.0: • Full fluid analyses are required, or flush the cooling system with water and refill with new Prestone Command ® HD Extended Life Antifreeze/Coolant or Prestone Command ® HD NF Extended Life Antifreeze/Coolant. • If the cooling system shows visible signs of contamination flush the system with Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser, then flush with water to remove chemical flush solvent and refill with Prestone Command ® HD Extended Life Antifreeze/Coolant or Prestone Command ® HD NF Extended Life Antifreeze/Coolant. 2. If the pH level is between 7.0 - 10.0 and the nitrite level is below 500: • The coolant is OK. • If needed top off with the correct amount of Prestone Command ® HD NF Extended Life Antifreeze/Coolant or water to adjust the level and concentration. 3. If the pH level is between 7.0 – 10.0 and the nitrite level is above 500: • Flush the cooling system with water and refill with new Prestone Command ® HD NF Extended Life Antifreeze/Coolant. • If the cooling system shows visible signs of contamination flush the system with Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser, then flush with water to remove chemical flush solvent and refill with Prestone Command ® HD NF Extended Life Antifreeze/Coolant. 4. If the pH level is above 10: • Flush the cooling system with water and refill with new Prestone Command ® HD NF Extended Life Antifreeze/Coolant. • If the cooling system shows visible signs of contamination flush the system with Prestone Command ® Heavy Duty Cooling System 2in1 Flush & Degreaser, then flush with water to remove chemical flush solvent and refill with Prestone Command ® HD NF Extended Life Antifreeze/Coolant. Part # AFC240 test strips are for Organic Acid Coolants ONLY, NOT for use with convention silicate (IAT) or hybrid organic acid coolants (HOAT). When utilizing Test Strips do not use the above color chart. Use the color chart on the Test Strip Bottle or individual card. HD NITRITE FREE EXTENDED LIFE COOLANT (NF OAT) Testing Fluid Conversion/Maintenance Plan Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Technical Service Bulletin Page 10 PCTSB-2017-01 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation Importance of Water Quality Testing Water Source When you use water to mix with antifreeze/coolant concentrate it is critical that the water be of the appropriate quality. Why should you check water quality? The quality of water can have a negative effect on the life and performance of the antifreeze/coolant by introducing excessive levels of corrosive ions, hard water salts, or pH destabilizing materials. Water quality is critical in order to prevent scale build-up and ensure that important chemicals in antifreeze/coolant mix- tures perform as expected and do not drop out of solution. Hardness Levels Water hardness level is determined by calcium and magnesium carbonate ion content. When water with high hardness is used in cooling systems, scale can form on cooling system surfaces and prevent efficient heat transfer. The net result can be excessive heat buildup leading to overheating, oil degradation, etc. pH Levels pH should remain in the appropriate range at all times. A pH that is too low or too high can destabilize the coolant inhibitor package causing the inhibitors to fall out of solution and in some cases form unstable gels. Any lost inhibitors can shorten the life of the coolant and reduce the corrosion protection provided by the coolant. If the pH of your water is too high or too low it should not be used to mix with antifreeze concentrates. Chloride Levels High chloride levels in water (sodium chloride) can increase the corrosion rate of aluminum and iron metal surfaces resulting in the depletion of important corrosion inhibitors out of the coolant. The net result is a reduction of corrosion protection of the engine cooling system. TEST INSTRUCTIONS Collect a water sample in a clean cup (about 8 oz.). Water sample must be between 50°F (10°C) and 130°F (54°C). Remove a strip from the bottle, DO NOT touch the pads at the end of the strip. Dip the strip in water sample for 5 seconds with a gentle, back and forth motion. Remove and shake strip briskly to remove excess liquid. Wait 25 seconds, then match Hardness and Chloride to the color chart. Match pH colors at 1 minute. When utilizing Test Strips do not use the above color chart. Use the color chart on the Test Strip Bottle or individual card. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone TSB for Training130009252017 Technical Service Bulletin Page 11 PCTSB-2017-01 PRESTONE PRODUCTS CORPORATION 1900 West Field Court, Lake Forest, IL 60045 ©2017 Prestone Products Corporation Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Prestone Flush Article for Training130009252017 CATALOG NUMBER 10 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ When in doubt, flush it out! One of the most frequently asked questions to our Prestone® technical team is, “When and how often should I flush the cooling system in my Heavy Duty truck?” and “What procedure should I use to flush the cooling system on a HD truck?” When should you flush the cooling system? 1. Whenever there are any signs of contamination in the system. The contamination could be oil, fuel, particulates, or hard water salts leaving deposits on cooling system metals. 2. If the vehicle has overheated. An overheated system can break down the coolant causing it to turn acidic, quickly causing component failures. 3. When the cooling system has been contaminated with multiple coolant types. For example, a truck operating with a HD extended life coolant was topped off with a conventional (green) coolant. This would lower the overall protection and may cause water pump failure or even cavitation pitting of the cylinder liners. If mixing coolant technologies is occurring, the cooling system will need to be flushed and the system refilled with a HD extended life coolant. 4. Flush the system whenever there is a cooling system component failure. If the component failed, it failed for a reason and likely left residual foreign material in the system. 5. A regular cooling system maintenance flush should be done whenever the coolant is at the end of the recommended mileage or time protection. Refer to the trucks owner’s manual for the recommended coolant change intervals. 6. Lastly, always remember the saying: when in doubt, flush it out! When flushing a HD cooling system always follow the OE Manufacturers flushing procedures. In a HD truck, flushing procedures can be different depending on the year, make, and model. It could be a universal flushing procedure, or a more intricate flushing procedure that requires a scan tool or laptop to open and close cooling system valves while flushing. Steps for a universal flushing procedure. • • When the engine is cold, start by completely draining the cooling system by loosening the radiator petcock drain. At this time you do not have to worry about the leftover coolant in the engine block, the flush solvent is designed to work with some coolant in the system. • • Tighten the radiator petcock drain and pour one gallon of Prestone® HD 2in1 Flush and Degreaser into the radiator or reservoir bottle and fill the rest of the system with water. • • Start the engine and let it run until it reaches normal operating temperature. Continue to run the engine for an additional 30-45 minutes with the heater set on high heat. Systems that are especially dirty or oily can be run for up to 3 hours. • • After the time has lapsed, shut off the vehicle and let the cooling system cool down. • • Open the radiator petcock and remove all engine block drain plugs to completely drain all water from the cooling system. You might have to disconnect the heater core inlet and outlet lines to completely drain the water from the heater core. • • Flush the system with water. Let the water run until the water coming out of the radiator drain and engine block drain plug holes is clear. If the heater core lines were removed, run water through these and back flush the heater core running water into the outlet hose until the water is clear and no debris is seen. • • Shut off the water and let the system drain. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Prestone Antifreeze Compatibility Reference Sheet for Trai CATALOG NUMBER 10 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Conventional (IAT) Antifreeze/Coolants Only use Conventional (IAT) AFC when mixing/top-off. Light-duty/Medium-duty Conventional Antifreeze/Coolants Color: Green, Yellow, other colors could be used. Check formulation before making decisions on mixing/top-off or converting to other Antifreeze/Coolants. No OEM’s for factory fill in North America. Compatible Prestone ® Product(s): Mixing/top-off PRIME ® by Prestone ® AF3200 & AF3300 Flush & Refill: Changing cooling system conventional AFC to Prime ® by Prestone ® (AF3200 & AF3300): Chemical flush required if cooling system shows any signs of contamination. Otherwise no flush required to properly drain & refill conventional antifreeze/coolant to PRIME ® by Prestone ® AF3200 & AF3300. Chemical flush recommended if converting the cooling system from conventional AFC to PRIME ® by Prestone ® AF3000/AF3100, AF3400/ AF3500 or Prestone ® with COR-GUARD AF2000/AF2100. Conventional AFC’s contain silicates, it is necessary to remove these silicates for proper protection to time or mileage. If not chemically flushing, it is required to flush the cooling system with water. Heavy-duty Conventional Antifreeze/Coolants SCA Pre-Charged Color: Green, Yellow, Purple, other colors could be used. Check formulation before making decisions on mixing/top-off or converting to other Antifreeze/Coolants. Compatible Prestone ® Product(s): Mixing/top-off PRIME ® by Prestone ® AF3200 & AF3300. Charged Coolant Filter should be installed and maintained according to OEM preventative maintenance schedules if equipped. Test SCA charge levels according to OEM preventative maintenance schedules are necessary. Add SCA’s (Prestone Command ® HD200) when needed. Mixing/top-off Prestone Command ® HD Antifreeze/Coolant AFC10000 & AFC10100. Charged Coolant Filter should be installed and maintained according to OEM preventative maintenance schedules if equipped. Test SCA charge levels according to OEM preventative maintenance schedules are necessary. Add SCA’s (Prestone Command ® HD200) when needed. Color of this AFC is Purple, when mixed with green AFC you will eventually turn the color of the AFC in the cooling system a brownish with a purple hue. This is normal color mixing, as long as there are NO contaminates in the cooling system and testing levels are normal, AFC is okay. Flush & Fill: Changing conventional AFC to Prime ® by Prestone ® (AF3200 & AF3300): Chemical flush required if cooling system shows any signs of contamination. Otherwise no flush required to properly drain & refill conventional antifreeze/coolant to PRIME ® by Prestone ® AF3200 & AF3300. On initial fill adding SCA’s (Prestone Command ® HD200) to proper test levels are required and a charged coolant filter should be installed and maintained for proper protection if equipped. Testing SCA charge levels according to OEM preventative maintenance schedules are necessary. Add SCA’s (HD200) when needed for proper protection. Changing conventional AFC to Prestone Command ® HD Antifreeze/Coolant AFC10000 & AFC10100. Chemical flush required if cooling system shows any signs of contamination. Otherwise no flush required to properly drain & refill conventional antifreeze/coolant to Prestone Command ® HD Antifreeze/Coolant AFC10000 & AFC10100. On initial fill adding SCA’s are not required and charged coolant filter should be installed and maintained for proper protection if equipped. Testing SCA charge levels according to OEM preventative maintenance schedules are necessary. Add SCA’s (Prestone Command ® HD200) when needed for proper protection. Converting to HD ELC NOAT or NF OAT: Chemical flush recommended if converting cooling system from conventional AFC to Prestone Command ® HD ELC Antifreeze/Coolants AFC11000/AFC11100 or AFC12000/AFC12100. Conventional AFC’s contain silicates, it is necessary to remove these silicates for proper protection to time or mileage. If not chemically flushing, it is required to flush the cooling system with water. Antifreeze/Coolant Compatibility Reference Sheet Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone Antifreeze Compatibility Reference Sheet for Trai Hybrid Organic Acid Technology (HOAT) G-05 is a HOAT AFC Light-duty/Medium-duty HOAT Antifreeze/Coolants Color: Yellow, Blue, Green, Pink other colors could be used. Check formulation before making decisions on mixing/top-off or converting to other Antifreeze/Coolants. Factory fill OEM’s presently European. Compatible Prestone ® Product(s): Mixing/top-off PRIME ® by Prestone ® AF3200/AF3300, AF3000/AF3100, and Prestone ® with COR-GUARD AF2000/AF2100. Flush & Refill: Changing cooling system from HOAT AFC to Prime ® by Prestone ® (AF3200 & AF3300): Chemical flush required if cooling system shows any signs of contamination. Otherwise no flush required to properly drain & refill with PRIME ® by Prestone ® AF3200 & AF3300. Chemical flush recommended if converting cooling system from HOAT AFC to PRIME ® by Prestone ® AF3000/AF3100, AF3400/ AF3500 or Prestone ® with COR-GUARD AF2000/AF2100. HOAT AFC’s contain silicates, it is necessary to remove these silicates for proper protection to time or mileage. If not chemically flushing, it is required to flush the cooling system with water. Heavy-duty HOAT Antifreeze/Coolants Color: Yellow, Blue, Red, other colors could be used. Check formulation before making decisions on mixing/top-off or converting to other Antifreeze/Coolants. Compatible Prestone ® Product(s): Mixing/top-off Prestone Command ® HD Antifreeze/Coolant AFC10000/AFC10100 and Prestone Command ® HD ELC Antifreeze/Coolant AFC11000/AFC11100. Flush & Refill: Changing cooling system from HOAT AFC to Prestone Command ® HD Antifreeze/Coolant AFC10000/AFC10100: Chemical flush required if cooling system shows any signs of contamination. Otherwise no flush required to properly drain & refill with Prestone Command ® HD Antifreeze/Coolant AFC10000/AFC10100. Chemical flush recommended if converting cooling system from HOAT AFC to Prestone Command ® HD ELC Antifreeze/Coolant AFC11000/AFC11100 or Prestone Command ® HD NF ELC Antifreeze/Coolant AFC12000/12100. HOAT AFC’s contain silicates, it is necessary to remove these silicates for proper protection to time or mileage. If not chemically flushing, it is required to flush the cooling system with water. Antifreeze/Coolant Compatibility Reference Sheet Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Prestone Antifreeze Compatibility Reference Sheet for Trai Antifreeze/Coolant Compatibility Reference Sheet Organic Acid Technology (OAT) If a coolant filter is equipped DO NOT USE a SCA charged coolant filter with HD ELC AFC’s. Only use a non-charged filter when equipped. Light-duty/Medium-duty OAT Antifreeze/Coolants Color: Y ellow, Orange, Pink, Purple, other colors could be used. Check formulation before making decisions on mixing/top-off or converting to other Antifreeze/Coolants. Factory fill OEM’s presently Ford, Chrysler, and General Motors. Compatible Prestone ® Product(s): Mixing/top-off Prestone ® with COR-GUARD AF2000/AF2100 (preferred top-off AFC) and PRIME ® by Prestone ® AF3000/AF3100 and AF3400/AF3500. Flush & Refill: Changing cooling system from OAT AFC to PRIME ® by Prestone ® AF3000/AF3100 or AF3400/AF3500, or Prestone ® with COR- GUARD AF2000/AF2100. Chemical flush required if cooling system shows any signs of contamination. Otherwise no flush required to properly drain & refill with PRIME ® by Prestone ® AF3000/AF3100 or AF3400/AF3500, or Prestone ® with COR-GUARD AF2000/AF2100. DEX-COOL ® AFC (General Motors, Ford & Navistar) Color: Orange Compatible Prestone ® Product(s): Mixing/Top-off with Prestone ® Dex-Cool ® Extended Life Antifreeze/Coolant AF888/AF850 (General Motors, Ford & Navistar approved), Prestone ® Extended Life Antifreeze/Coolant with COR-GUARD AF2000/AF2100, or PRIME ® by Prestone ® AF3400/ AF3500 or AF3000/AF3100. Flush & Refill: Changing cooling system from DEX-COOL ® AFC formulation to Prestone ® Dex-Cool ® Extended Life Antifreeze/Coolant AF888/ AF850, PRIME ® by Prestone ® AF3400/AF3500 or AF3000/AF3100, or Prestone ® with COR-GUARD AF2000/AF2100. Chemical flush required if cooling system shows any signs of contamination. Otherwise no flush required to properly drain & refill with Prestone ® Dex-Cool ® Extended Life Antifreeze/Coolant AF888/AF850, PRIME ® by Prestone ® AF3400/AF3500 or AF3000/AF3100, or Prestone ® with COR-GUARD AF2000/AF2100. DEX-COOL ® is a Registered Trademark of General Motors Corp. Heavy-duty NOAT Antifreeze/Coolants Color: Red, other colors could be used. Check formulation before making decisions on mixing/top-off or converting to other Antifreeze/Coolants. Compatible Prestone ® Product(s): Mixing/top-off Prestone Command ® HD ELC Antifreeze/Coolant AFC11000/AFC11100 or Prestone Command ® HD NF ELC Antifreeze/Coolant AFC12000/12100. Flush & Refill: Changing cooling system from HD NOAT AFC to Prestone Command ® HD ELC Antifreeze/Coolant AFC11000/AFC11100 or Prestone Command ® HD NF ELC Antifreeze/Coolant AFC12000/12100. Chemical flush required if cooling system shows any signs of contamination. Otherwise no flush required to properly drain & refill with Prestone Command ® HD ELC Antifreeze/Coolant AFC11000/AFC11100 or Prestone Command ® HD NF ELC Antifreeze/Coolant AFC12000/12100. Chemical flush recommended if converting cooling system from NOAT AFC to Prestone Command ® HD Antifreeze/Coolant AFC10000/ AFC10100. If not chemically flushing, it is required to flush the cooling system with water. If a coolant filter is equipped DO NOT USE a SCA charged coolant filter with HD ELC AFC’s. Only use a non-charged filter when equipped. Heavy-duty NF OAT Antifreeze/Coolants Color: Yellow or Red, other colors could be used. Check formulation before making decisions on mixing/top-off or converting to other Antifreeze/Coolants. Compatible Prestone ® Product(s): Mixing/top-off Prestone Command ® HD NF ELC Antifreeze/Coolant AFC12000/12100. Flush & Refill: Changing cooling system from HD NF OAT AFC to Prestone Command ® HD NF ELC Antifreeze/Coolant AFC12000/12100. Chemical flush required if cooling system shows any signs of contamination. Otherwise no flush required to properly drain & refill with Prestone Command ® HD NF ELC Antifreeze/Coolant AFC12000/12100. It is not recommended to convert HD NF OAT AFC filled cooling systems to other AFC NOAT, HOAT, IAT, etc. formulations. If a coolant filter is equipped DO NOT USE a SCA charged coolant filter with HD ELC AFC’s. Only use a non-charged filter when equipped. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Power Serivce Diesel Fuel Supplement and Kleen TechTips130 Diesel Fuel Supplement ® +Cetane Boost ® is a winterizer/antigel that is used in the cold weather months to prevent fuel gelling and keep fuel-filters from plugging with ice and wax. It provides trouble-free winter operation for diesel fuel. Benefits Prevents fuel gelling Protects against fuel-filter icing Boosts cetane for faster cold starts Contains Slickdiesel® Lubricator to protect fuel pumps and injectors from increased wear caused by Ultra Low Sulfur Diesel (ULSD) fuel Effective in all diesel fuels including ULSD and biodiesel blends Prevents Fuel Gelling and Protects Against Fuel-Filter Icing To maximize performance in cold temperatures, Power Service has developed the most advanced cold-flow improver technology available today for all diesel fuels, including Ultra Low Sulfur Diesel (ULSD) fuel and biodiesel blends. Diesel Fuel Supplement is designed to prevent fuel-filter plugging by modifying the size and shape of the wax crystals so they remain small enough to flow through fuel-filters without plugging. It also prevents the wax crystals from settling to the bottom of fuel tanks during storage. Diesel Fuel Supplement also contains a de-icer to help prevent fuel-filter and fuel-line freezing caused by water. DIESEL FUEL SUPPLEMENT MODIFIES WAX IN DIESEL FUELS UNTREATED TREATED DIESEL FUEL SUPPLEMENT ® +CETANE BOOST ® Diesel Fuel Supplement ® +CetaneBoost ® isendorsedand recommendedbyCummins ® Diesel Fuel Supplement ® +Cetane Boost ® is a winterizer/antigel that is used in the cold weather months to prevent fuel gelling and keep fuel-filters from plugging with ice and wax. It provides trouble-free winter operation for diesel fu l. Benefits Prevents fuel gelling Protects against fuel-filter icing Boosts cetane for faster cold starts Contains Slickdiesel® Lubricator to protect fuel pumps and injectors from increased wear caused by Ultra Low Sulfur Diesel (ULSD) fuel Effective in all diesel fuels including ULSD and biodiesel blends Prevents Fuel Gelling and Protects Against Fuel-Filter Icing To maximize performance in cold temperatures, Power Service has developed the most advanced cold-flow improver technol gy available today for all diesel fuels, including Ultra Low Sulfur Diesel (ULSD) fuel and biodiesel blends. Diesel Fuel Supplement is designed to prevent fuel-filter plugging by modifying the size and shape of the wax crystals so they remain small enough to flow through fuel-filters without plugging. It also prevents the wax crystals from settling to the bottom of fuel tanks during storage. Diesel Fuel Supplement also contains a de-icer to help prevent fuel-filter and fuel-line freezing caused by water. Without Diesel Fuel Supplement, large wax crystals block filters and transfer lines, causing fuel gelling. With Diesel Fuel Supplement, small, compact wax crystals flow in suspen- sion for trouble-free winter operation DIESEL FUEL SUPPLEMENT MODIFIES WAX IN DIESEL FUELS UNTREATED TREATED DIESEL FUEL SUPPLEMENT ® +CETANE BOOST ® Diesel Fuel Supplement ® +CetaneBoost ® isendorsedand recommendedbyCummins ® Diesel Fu l Supp ement ® +C tane Boost ® is a winterizer/antigel that is used in the cold weather months to prevent fu l gelling and keep fu l-filters rom plugging with ice and wax. It provides trouble-free winter op ration for diesel fu l. Benefits Prevents fuel gelling Protects against fuel-filter icing Boosts cetane for faste cold starts Contains Slickdiesel® Lubricato to pro ect fu l pumps and injectors from increased wear caused by Ultra Low Sulfur Diesel (ULSD) fuel Effective in all d ese fu ls includ g ULSD and biodiesel bl nds Prevents Fuel Gelling and Protects Against Fuel- ilter Icing To maximize performance in cold temperatures, Pow r Service has developed the most advance cold-flow improver technology available today for all diesel fuels, including Ultra Low Sulfur Diesel (ULSD) fuel and biodiesel blends. Di sel Fu l Supplement is d signe to prevent fuel-filter plugging by modifying the size and shape of the wax crystals so they remain small enough to flow hrough fuel-filters without plugging. It also prevents th wax crystals from settling to the b t om of fuel tanks duri g sto age. Diesel Fu l Supplement also contains a de-icer to help prev nt fuel-filter and fuel-line freezing caused by water. Without Diesel F el Supplement, large wax crystals block filters and tran fer lines, caus g fuel gelling. With Diesel Fuel Supplement, small, compact wax crys als flow in suspen- sion for trouble-f ee winter operation DIESEL FUEL SUPPLEMENT MODIFIES WAX IN DIESEL FU LS UNTREATED TREATED DIESEL FUEL SUPPLEM NT ® +CETANE BOOST ® Diesel Fuel Supplement ® +CetaneBoost ® isendorse and recommendedbyCummins ® Diesel Fuel Supplement ® +Cetane Boost ® is a wi rizer/antig l that is used in he cold weather months to prevent fuel gelling and keep fuel-filt s from plugging with ice and wax. It provides trouble-free winter operation for diesel fuel. Benefit Prevents fuel gelling Protects against fuel-filter icing Boosts cetane for fast r cold starts Contains Slickdiesel® Lubricator to protect fuel pumps and injectors from increased wear caused by Ultra Low Sulfur Diesel (ULSD) fuel Effective in all diesel fuels including ULSD and biodiesel blends Prevents Fuel Gelling and Protects Against Fuel-Filter Icing To maximize performance in cold temperatures, Power Service has developed the most advanced cold-flow i prover technology available oday for all diesel fuels, including Ultra Low Sulfur Dies l (ULSD) fuel and bi dies l blends. Diesel Fu l Supplement s designed to prevent fuel-fi er plugging by modifying the size and shap of the wax crystals so they remain small enough to flow through fuel-filters without plugging. t also pr vents the wax crystals from settl g to the bottom of uel anks during storage. Diesel Fuel Supplement also co tains a de-i er to help prevent fuel-filt r and fuel-line freezing caused by water. DIESEL FUEL SUPPLEMENT MODIFIES WAX IN DIESEL FUELS UNTREATED TREATED DIESEL FUEL SUPPLEMENT ® +CETANE BOOST ® Diesel Fuel Supplement ® +CetaneBoost ® isendorsedand recommend dbyCummins ® TECHNICAL BULLETIN recommended by Cummins ® CATALOG NUMBER 10 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Power Serivce Diesel Fuel Supplement and Kleen TechTips130 513 Peaster Highway • Weatherford, Texas 76086-1089 817.599.9486 • 800.643.9089 Power Service Products, Inc. ©2017 05.05.17 25457 DIRECTIONS FOR USE Add Diesel Fuel Supplement +Cetane Boost as directed on the container label. To ensure thorough mixing, add prior to filling tanks with diesel fuel. PART# PACK TREATS CUSTOMER CONVENIENCE +CETANE BOOST FORMULA – 1:400 TREATMENT RATIO 1016-09 9/1 16-Ounce Up to 40 Gallons 1025-12 12/1 32-Ounce Up to 100 Gallons 1080-06 6/1 80-Ounce Up to 250 Gallons CONCENTRATED +CETANE BOOST FORMULA – 1:1,000 TREATMENT RATIO 1128-04 4/1 One-Gallon Up to 1,000 Gallons 1060 260-Gallon Tote Up to 260,000 Gallons CONCENTRATED +CETANE BOOST FORMULA – 1:1,500 TREATMENT RATIO 1050-02 Two/2.5-Gallon Up to 3,750 Gallons 1055 55-Gallon Drum Up to 82,500 Gallons 1260 260-Gallon Tote Up to 390,000 Gallons 1000 6,000-Gallon Min. Up to 9,000,000 Gallons Boosts Cetane There is a direct relationship between a diesel fuel’s cetane number and its ignition point. Delayed ignition is a primary cause of increased emissions and inferior engine performance. The lower the cetane number, the longer the ignition delay. Fuels with high cetane numbers burn more quickly and more completely, resulting in smoother running engines with less power lag and easier engine starting. TYPICAL PHYSICAL PROPERTIES OF DIESEL FUEL SUPPLEMENT +CETANE BOOST Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brown Density (lbs/gal) Customer Convenience +Cetane Boost Formula (1:400). . . . . . . . . . . . . . . . . . . . 7.7 Concentrated +Cetane Boost Formula (1:1,000) . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 Concentrated +Cetane Boost Formula (1:1,500) . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.8 Sulfur Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <15 parts per million (ppm) Flash Point Customer Convenience +Cetane Boost Formula (1:400) . . . . . . . . . . . . . . . . . 101°F. Concentrated +Cetane Boost Formula (1:1,000) . . . . . . . . . . . . . . . . . . . . . . . . . 110°F. Concentrated +Cetane Boost Formula (1:1,500) . . . . . . . . . . . . . . . . . . . . . . . . 107°F. Pour Point Customer Convenience +Cetane Boost Formula (1:400) . . . . . . . . . . . . . . . . . -70°F. Concentrated +Cetane Boost Formula (1:1,000) . . . . . . . . . . . . . . . . . . . . . . . . -30°F. Concentrated +Cetane Boost Formula (1:1,500) . . . . . . . . . . . . . . . . . . . . . . . . .-15°F. Minimum Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10°F. Solubility In Diesel Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Completely Soluble In Biodiesel Blends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Completely Soluble In Home Heating Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Completely Soluble In Kerosene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Completely Soluble Shipping and Handling Part Nos. 1016, 1025, 1080, 1128, 1050, 1055. . . . . . . . . . . . . . . . Not regulated by DOT Part Nos. 1060, 1260 . . . . . . . . . . . . . . . . . . . . . . . . . Combustible Liquid N.O.S. NA 1993 . . . . . . . . . . . . . . . . . . . . . (Petroleum Distillates) Marine Pollutant (2-Ethylhexyl Nitrate) Diesel Fuel Supplement +Cetane Boost is safe for use in all diesel engines. This diesel fuel additive complies with the federal low sulfur content requirements for use in diesel motor vehicles and nonroad engines. H igh Frequency Reciprocating Rig (HFRR) evaluates the lubricity of diesel fuel. The Wear Scar Diameter (WSD) maximum is 520 microns. A WSD measuring larger than 520 does not meet lubricity specifications. FAIL (650 WSD) PASS (400 WSD) Endorsed and recommended by Cummins® DIESEL FUEL SUPPLEMENT ® +CETANE BOOST ® Diesel Fuel Supplement ® +CetaneBoost ® isendorsedand recommendedbyCummins ® Contains Slickdiesel ® for Maximum Fuel Lubrication Slickdiesel is a proprietary Power Service diesel fuel lubricator that sets the standard for lubrication of diesel fuel injection systems. The components of diesel fuel injection systems are lubricated by diesel fuel. Without proper lubrication, fuel injectors and pumps are subjected to increased wear rates and premature failure. Diesel Fuel Supplement ® +Cetane Boost ® contains Slickdiesel and exceeds the ASTM D-975 specification of 520 Wear Scar Diameter (WSD) for lubricity in diesel fuel, allowing operators to achieve the EMA recommended 460 WSD. PART# PACK TREATS CUSTOMER CONVENIENCE +CETANE BOOST FORMULA – 1:400 TREATMENT RATIO PS 1016-09 9/1 16-Ounce Up to 40 Gallons PS 1025-12 12/1 32-Ounce Up to 100 Gallons PS 1080-06 6/1 80-Ounce Up to 250 Gallons CONCENTRAT D +CETANE BOOST FORMULA – :1,000 TREATMENT RATIO PS 1128-04 4/1 One-Gallon Up to 1,000 Gallons PS 1060 260-Gallon Tote Up to 260,000 Gallons CONCENTRATED +CETANE BOOST FORMULA – 1:1,500 TREATMENT RATIO PS 1050-02 Two/2.5-Gallon Up to 3,750 Gallons PS 1055 55-Gallon Drum Up to 82,500 Gallons PS 1260 260-Gallon Tote Up to 390,000 Gallons PS 1000 6,000-Gallon Min. Up to 9,000,000 Gallons Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 10Power Serivce Diesel Fuel Supplement and Kleen TechTips130 DIESEL KLEEN ® +CETANE BOOST ® Diesel Kleen ® +Cetane Boost ® is a total injector cleaner and performance improver that cleans injectors, boosts cetane and lubricates fuel injection components. It restores lost power, smooths rough-running engines and improves fuel economy up to 8%. Benefits Cleans dirty injectors and prevents injector sticking in both High Pressure Common Rail (HPCR) and older systems Removes both Internal Diesel Injector Deposits (IDIDs) and external deposits (nozzle coking) that decrease power and fuel economy Boosts cetane up to 6 numbers - engines run smoother with less power lag and faster cold starts Boosts power - reduces need for downshifting Improves fuel economy up to 8% Contains Slickdiesel® Lubricator to protect fuel pumps and injectors from increased wear caused by Ultra Low Sulfur Diesel (ULSD) fuel Prevents asphaltene formations and thermal breakdown of diesel fuel - protects against sludge formations that plug fuel-filters and injectors Provides superior corrosion protection Effective in all diesel fuels, including ULSD, biodiesel and biodiesel blends Advanced OEM Recommended Injector Cleaning Technology Power Service Diesel Kleen +Cetane Boost is formulated with the most effective diesel injector detergent technology in the industry to provide maximum clean-up and prevention of diesel deposits found in modern direct injection diesel engines. This technology prevents and restores lost power and fuel economy caused by both Internal Diesel Injector Deposits (IDIDs) and external deposits (nozzle coking). These deposits cause injector sticking and disrupt fuel flow into the combustion chamber. Diesel Kleen +Cetane Boost provides accelerated clean-up and keeps-clean performance in all industry standard diesel injector deposit tests including: DW10B, DW10C and XUD-9. The engine operational improvements are significant: • Improved fuel economy up to 8% • Increased power and reduced need for downshifting • Smoother and quieter engine operation Boosts Cetane up to 6 Numbers There is a direct relationship between a diesel fuel’s cetane number and its ignition point. Delayed ignition is a primary cause of increased emissions and inferior engine performance. The lower the cetane number, the longer the ignition delay. Fuels with high cetane numbers burn more quickly and more completely, resulting in smoother running engines with less power lag, lower emissions and easier engine starting. High Pressure Common Rail injectors before and after clean-up with fuel treated with Diesel Kleen +Cetane Boost. DW10B DIESEL FUEL INJECTOR FOULING TEST BEFORE AFTER DieselKleen ® +CetaneBoost ® isendorsedandrecommended byCummins ® Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Penray Summer Products130004212021 SUMMER PRODUCTS ULSD Compliant ▪ Eliminates over-inhibited cooling systems ▪ Reduces cost ▪ Minimizes waste Pow-R Performance ™ Diesel Fuel Enhancer Need Release ® Extended Service Coolant Filter Oil Purge Cooling System Cleaner NA 200264 ▪ Specifically formulated to remove oil, hydraulic & transmission fluid from heavy duty cooling systems ▪ Disperses dropout ▪ Requires less flushing than other cleaners ▪ Won’t harm seals & metals On-Line Cooling System Cleaner NA 200164 ▪ Cleans diesel engine cooling systems while they remain in service ▪ Eliminates light scale & corrosion formation ▪ Removes harmful mineral & oxide deposits ▪ Cost effective alternative to in-shop cleaning P/N Size Treats Concentrated Fuel Prep NA 201201 1 gallon 12,500 gallons NA 201205 5 gallons 62,500 gallons Fuel Prep 2012 NA 100012 12 fl. oz. 50 gallons NA 100032 32 fl. oz. 250 gallons NA 100005 5 gallons 7,500 gallons NA 100055 55 gallons 82,500 gallons Year-Around Diesel Fuel Conditioner ▪ Ready for use in BioDiesel ▪ Eliminates bacterial & fungal growth ▪ Eliminates & disperses sludge ▪ Prevents corrosion & conditions fuel Fuel Prep Diesel Fuel Conditioner P/N Size Treats NA 105032 32 fl oz. 250 gallons NA 105005 5 gallons 5,000 gallons Total Diesel Fuel System Cleaner Compatible with bio-diesel blends ▪ Dissolves and disperses asphaltenes ▪ Great year around cleaner ▪ Enhances overall performance of fuel ▪ Cleans and unplugs injectors ▪ Helps improve lubricity ▪ Helps prevent fuel system corrosion ▪ Improves Power ▪ Attacks extreme cases of dirt, grime and sludge ▪ Helps prevent degraded fuel from plugging fuel filters or injectors ▪ Contains extra solvents and detergents ▪ Helps disperse water ▪ Restores cetane ▪ Individual and bulk applications available ▪ BioDiesel and ULSD compliant Don’t Neglect Your Summer Fuel Treat it with Penray to ensure that it gives you the power you need! Water allows bacteria and fungus to grow in all diesel fuels, and bulk storage tanks are a perfect environment for excessive growth. BioDiesel, derived from living organisms, fosters increased growth of microorganisms. CATALOG NUMBER 10 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ ▪ Ready for use in BioDiesel ▪ ULSD compliant ▪ Lubricity additive ▪ Cetane improver ▪ Maximizes fuel lubrication ▪ Increases power ▪ Stabilizes stored fuel ▪ Reduces Nox ▪ Cleans injectors ▪ Decreases fuel consumption NA 208005 5 Gallons Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Penray Coolant Chart130004212021 PENRAY COOLANT CHART FOR MAINTAINING 50% ANTIFREEZE +32 0% System Capacity (Gallons*) System Capacity (Gallons*) +25 10% +20 15% +15 20% +10 25% +5 30% -5 35% -12 40% -23 45% -34 50% -50 55% -65 60% -75 65% -84 70% -70 75% -55 80% -43 85% -30 90% -5 100% Drain Coolant and Add Concentrated Antifreeze (Quarts) Freeze Point (deg. F) vs. Percent Antifreeze Drain Coolant and Add Water (Quarts) If the reading on your refractometer does not appear on the chart, the solution is over concentrated. Drain your system and start over by adding a 50/50 mix of Fleetcharge ® or DDC Powercool ® and water to your engine’s system. * 1 Gallon = 4 Quarts Coolant fundamentally consists of three components: WATER- Water is an excellent heat transfer fluid, but it can freeze, and causes engine components to corrode. GLYCOL- Glycol is added to provide freeze and boil-over protection. It reduces the heat transfer capability of water. It is usually mixed 50/50 with water. SUPPLEMENTAL COOLANT ADDITIVES (SCA’s)- Fully Formulated coolants contain many of the same chemical additives, regardless of brand. Nitrites are added to coolant to protect iron and steel components from cavitation, pitting and rust corrosion. Nitrates provide solder and aluminum protection. Silicate is also added to protect aluminum surfaces. Tolytriazole (TT) and sometimes Mercaptobenzothiazole (MBT) are used to protect copper and brass metals. Phosphate or Borate are pH buffers used to control alkalinity. The WATER and GLYCOL in your coolant will remain in service indefinitely, barring any contamination. The SUPPLEMENTAL COOLANT ADDITIVES (SCA’s) will become depleted and must be replaced per manufacturers recommendation. For a tested and proven cooling maintenance procedure, use Penray’s FILL-FOR-LIFE ® program. Utilize NEED-RELEASE ® filters to protect your engine for 150,000 miles or use PENCOOL ® cooling system liquids and maintenance filters. Pencool ® 3000 P/N NA 300016 & NA 300064 Oil Purge P/N NA 200264 2001 Cleaner P/N NA 200164 Refractometer P/N PG R-METER Fahrenheit Test Strips P/N NA TS200 Pencool ® w/ Stabil-Aid ® Cooling Filter P/N NA NF3000 Need-Release ® Filter P/N NA NF2088SM, NA NF2095SM, NA NF2096SM Coolant Filter Elements P/N NA NF3088SM & NA NF3999SM CATALOG NUMBER 10 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Lucas Oil Pump Program130004212021 CATALOG NUMBER 10 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 TRUCK PARTS SUPER STORE TM KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 JOPLIN 2424 Stephens Blvd. main 417.717.6022 fax 417.782.7126 parts 866.318.9111 Lucas Oil’s Drum and Tote Free Pump Credit Policy Lucas Oil has instituted a policy regarding the purchasing and reimbursement of pumps for use on drums or totes containing Lucas Oil products. Purchase a pump from Midwest Wheel and you will be credited back the amount of the pump after purchasing the quantity of drums or totes listed below. Pump P/N Container Type Price Purchase Quantity Required for Credit LUC11000 Drum $1,363.75 20 LUC10982 Tote $1,812.50 6 Additional Information: • A pump can be used for the SKU solely that it was purchased for and not transferred to other drums or totes to qualify for the credit • Pump must be purchased with the first drum(s) or tote(s) • Credit will be sent after payment is received on purchase order showing quantity requirement is met • Pumps are high quality including a meter and reel November 30, 2020 (10Lucas Oil Pump Program) Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Lucas Diesel Oil and Shell Valvoline Products130003042021 CATALOG NUMBER 10 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ SAE 15W-40 Magnum CK-4 Diesel Oil LUC10287 1 Gallon (Case of 4) LUC10288 5 Gallon Pail (1 Pail) LUC10289 55 Gallon Drum (1 Drum) LUC10292 Per Gallon Tote (1 Tote) Lucas CK-4 is a premium Heavy Duty Motor Oil blended with high quality API Group II and Group Ill base oils and a cutting-edge additive package providing the robust performance required by modern diesel engines while assuring good fuel economy. KEY BENEFITS • • Longer engine life • • Extended oil changes • • Lower soot levels • • Less filter maintenance • • Less oxidation • • Lower oil consumption • • High temperature stability • • Exclusive Lucas formula • • Safely blends with other motor oils SAE 15W-40 Magnum CK-4 DIESEL OIL Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Bioguard Biocide130004212021 CATALOG NUMBER 10 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ BIOGUARD ™ ULS (BGDULS) FUEL BIOCIDE Microorganisms, like bacteria, yeast and mold are known as “bugs.” “Bugs” live in virtually all diesel fuel systems. Wherever there is moisture and fuel together there is a good environment for biological growth. The most common places for contamination include the fuel/water interface near tank bottoms, on storage tank walls, and in tank bottom sediment. Microorganisms live in the water found in all fuel systems and eat the fuel as a nutrient source. Sulfur provides some natural protection against bacteria growth. However, with the introduction of ULSD fuels, there is minimal natural protection to prevent biological growth in fuel systems. Left unchecked, “bugs” will corrode fuel systems and create slime & sludge that plug fuel filters and fuel lines. The result is increased maintenance costs and expensive down time. BioGuard ™ ULS is an EPA registered, fuel & water soluble, dual phase microbiocide that effectively kills bacteria, fungi & other microorganisms that grow in gasoline, diesel fuel, biodiesel blends and heating oil storage tanks. It also helps prevent fuel system contamination from new infections. » Kills bacteria (“bugs”), yeast, mold, and other microorganisms. » Kills bacteria in the fuel and water phase. » Works faster & more effectively (as little as 2-3 hours). » Prevents bio-contamination of fuel system. » Prevents bacteria caused filter plugging. » Prevents bacteria caused fuel line plugging. » Prevents and breaks up bacteria caused sludge and slime. » Prevents bacteria caused corrosion. » Prevents equipment down time. » Effective in gasoline, diesel, biodiesel blends, & heating oil. » Safe for use in on-road and off-road fuels. » Initial Treat Rate 1:2500, Maintenance Treat Rate 1:7400 16 oz bottle treats 460 gallons at initial treat rate and up to 920 gallons for maintenance dosage. P/N Description Case NA BGDULS2016OZ 16 oz. 12 NA BGDULS201GAL 1 Gallon 2 Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

10Krown Fleet New130004212021 RUST INHIBITOR KL73 RUST INHIBITOR / LUBRICANT • Dielectric strength 50kv, safe on all electrical • Remains active despite washing or road wash • Effective in high and low temperatures • Food grade approved throughout North America • Actively displaces moisture • Solvent-free Spray Tools Available! Aerosol CR KA71400-12 1 gal. CR KA74004-4 5 gal. CR KA74020 55 gal. CR KA74205 CATALOG NUMBER 10 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ SALT ELIMINATOR CHLORIDE REMOVING DETERGENT • Easily rinses to a beading,waxy finish • Removes even heavy salt build up quickly and easily • Reduces surface rust • Can be used in any wash system • Designed for heavy duty applications • Contains no solvents, NPEs or VOCs ORDER NUMBER Aerosol CR KA1198-12 1 gal. CR KA1199-4 5 gal. CR KA1200 55 gal. CR KA1201 DILUTION RATIO Heavy Duty 3:1 Recommended 10:1 Light Duty 20:1 • Solvent-free • Food grade approved throughout North America • Extremely durable • Advanced surface modifying additive • Displaces moisture / protects against rust • Remains on surface, does not evaporate • Designed for extreme heat & heavy load • Environmentally-friendly ORDER NUMBER Aerosol CR KA63400-12 5 gal. CR KA63020 KLFSM CHAIN LUBRICANT ORDER NUMBER Aerosol CR KA51400-12 KP53 FAST-ACTING PENETRANT • Allows for repair and maintenance without concern of contamination • Safe for use with all metals and electrical systems • Fast, effective penetrating action greatly outperforms other food approved penetrants • Food grade approved throughout North America • Breaks through rusted and seized parts for easy teardown With Krown Products you will receive all of these benefits... » Fewer highway breakdowns » Downtime will be reduced » Longer life cycle for vehicles » Increased resale value Resulting in... A better looking, longer lasting, safer vehicle! Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

08Meritor Brake TechTip130008062019 TECH Tips How About a Little More Brake and a Little Less Shake? Today’s RSD (Reduced Stopping Distance) compliant vehicle steer axles, with their increased size and torque, are more susceptible than prior vehicles to braking vibration issues due to assembled brake TIR (Total Indicator Reading). Three major factors contribute to assembled brake TIR; drum run-out, hub-to- drum mating surfaces/pilots and wheel bearing adjustment. You must check TIR on a brake drum in an assembled brake. Do not disassemble the wheel/tire assembly, brake drum from hub or any other components prior to initial TIR inspection. Disassembly will change the original position of the assembled components and may vary TIR readings/performance. If assembled TIR exceeds 0.015-inch (0.381 mm): • • Remove the drum and inspect the components. Damaged and corroded hub-to-drum mating surfaces/pilots are becoming a common cause of vibration complaints. • • Verify wheel bearing adjustment. Wheel bearing end play must be within the required 0.001”-0.005” or be properly preloaded with Dr. Preload or assemble brake TIR will be increased. Excessive end play can cause the drum braking surface to not be concentric to the bearings/spindle. If damaged is found, replace the necessary components, re-assemble and verify TIR is within specification IMPORTANT: For proper brake balance and performance: • • Verify that all brake drum diameters on an axle are within 0.025’ • • Verify all brake drums are under 0.080’ of wear, allowing for wear during current service interval • • Verify brake drums are all of equal original weight • • Verify that the original Brake drum weight is proper to dissipate the heat generated by this brake in the current application MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 E. 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 TRUCK PARTS SUPER STORE TM August 6, 2019 (08Meritor Brake TechTip) CATALOG NUMBER 08 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

08Hendrickson Spider Brake Identification and Fontaine Cold TECH Tips CATALOG NUMBER 08 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ Hendrickson 12.25" Brake Identification Key Identification Tips: The Hendrickson HXS 12.25" x 7.00" brake design is very similar to the 4692FC2 . It is important to use the 4692HEN shoe with the Hendrickson Spider. Spider: Look for the near the camshaft end of the spider on the outside face Spider ID Bosses: Look for these key features Hole located under anchor pins to assist in ABS installation Offset coil pack on retaining spring Bosses for Dust Shield mount, 4 places – Likely not drilled Zerk Grease Fitting If you have the Hendrickson be sure to install the 4692HEN shoes for proper brake performance Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

08Brake Inspections Tech Tip130007032019 TECH Tips CATALOG NUMBER 08 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ Bad brakes: Why regular brake inspections are vital to reducing downtime, roadside violations www.truckpartsandservice.com By Tom Quimby Read any good drums lately? Brake drums help tell the critical story of overall brake performance, which is important since an overwhelming portion of violations — 45 percent during last year’s Commercial Vehicle Safety Alliance (CVSA) Inspection Blitz — were owed to bad brakes. In the age of ‘hurry up and get it done’ simply replacing a brake drum and shoes is not an effective way to maximize brake life, safety and productivity. Nor is it the best way to avoid costly violations and irate drivers. “This is the second time they’ve done this to me,” said a driver recently to a Florida Highway Patrol trooper who grounded his truck for bad brakes. The ‘they’ in this case would be the fleet that failed to ensure that the driver’s trailer had sound brakes before hitting the road. But the driver also shares responsibility since the trailer should pass his own inspection prior to hauling. The grounded truck and its driver sat and waited at an inspection station along Interstate 10 for a tech to show up to fix the brakes. Both were still there when the trooper’s shift ended, and with a load that was going nowhere fast. Avoiding violations not only comes from keeping brakes in adjustment it also comes from taking a close look at brake drums, which can reveal how the overall system is performing. Tossing out a drum without closely inspecting it for wear patterns and damage may mean missing vital clues that can point to issues with hardware, shoes and the smallest of road hazards like dirt and sand. “Any irregular wear patterns should be investigated, such as tapered wear across the braking surface or significant grooving beyond the specific drum’s maximum wear diameter,” says Johnathon Capps, vice-president of engineering, Webb Wheel Products. “Causes for this include worn braking hardware (such as the rollers and bushings), dirt and debris infiltration across the braking surface, and inadequate friction material.” Accuride’s director of wheel end product engineering, Greg Sturdy, says on average fleets are not conducting enough brake drum inspections. For guidance, Sturdy points to the following recommended practices from the American Trucking Associations’ Technology & Maintenance Council (TMC): TMC RP608 on Brake Drums and Rotors; RP627 Brake Lining Structural Defects; and RP 629 Brake Lining Contamination. “Even wear is critical,” Sturdy says. “If there is any sign of uneven wear or heat discoloration this indicates the system is not running true to the axis of rotation and causing runout. Such runout will cause the brake components to unevenly heat and cool and cause accelerated wear along with crack formation potential.” Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 08Brake Inspections Tech Tip130007032019 Sturdy adds that grooving can also be caused by aggressive linings, improper brake setup and improper burnishing. Since brakes are only as good as their hardware be sure to take a close look when the drum is removed. “Look for damage to components, cracks loose or missing fasteners, corrosion, etc.,” Capps says. “Refer to the manufacturer’s maintenance manuals for specific dimensional inspection points. Also refer to the manual to determine where to lubricate and where not to lubricate.” Excessive lubrication can make its way to the drum’s braking surface and shoes, get in the way of effective braking and lead to premature wear, adds Kevin Pfost, coordinator of technical services, Bendix Spicer Foundation Brake (BSFB). Pfost says that while grooving can be caused by foreign material like sand and dirt entering the drum it also may be the result of excessively hard brake shoes. Picking high-quality shoes to match the duty cycle can help avoid trouble down the road. “If the drum is wearing faster than expected, then there may be a friction couple incompatibility or that particular wheel end is doing more work than other wheel ends,” says Joseph Kay director of brake engineering, Meritor. Wear patterns like grooving, however, aren’t always indicative of a problem. “A groove on the outer edge of the drum is quite common as the drum is typically slightly larger in width than the shoe,” says Mike Hasinec, vice president of maintenance, Penske Truck Leasing. “Deep grooves throughout the drum surface typically indicate the brake lining has worn down to the rivets. Pitting can be an indication of debris getting in the drum — backing plates help prevent that. Some very small cracks inside the drum surface are normal. In rare cases, you may see the drum worn more towards the outside versus the inside. An alignment problem or even a bent or twisted brake spider can cause this.” The heat is on Since it takes plenty of friction to slow down an 80,000-lb. truck it’s not hard imagining how hot brakes can get and the impact that heat can have on drums. Gray iron is the standard material used in brake drum manufacturing. However, according to Kay, variance in composition can affect thermal characteristics of the drum. The lower the thermal properties, the higher the thermal stress to the drum. Costly elements like molybdenum combined with gray iron can help increase strength but the heat will always be present along with its effects which, if left unchecked, can result in drum failure. “The main function of a brake drum or rotor is to convert energy to achieve a vehicle deceleration,” Kay says. “The drum does this by converting the rubbing friction into thermal energy (heat) and then release the thermal energy to the atmosphere. The drum must have excellent material properties to manage the energy quickly and efficiently. “For example, an emergency stop with a fully-loaded commercial truck from 60 mph will happen under six seconds, therefore if the energy cannot convert quickly the result will be a longer stopping distance.” Obviously, no one wants a longer stopping distance, which is a vital reminder of the importance of choosing the right brake components and conducting routine and thorough inspections that include looking for signs of overheating. “The drum has to handle a lot of variation in temperature,” Hasinec says. “During braking the drum experiences expansion and contraction, which causes many of the smaller cracks you see on the inner drum surface. These smaller cracks are generated from the heat of the braking event and are normal. A lot of heat and a panic stop usually causes larger cracks that can actually be seen from the outer edge of the drum. This is a drum that you discard, as it is usually cracked all the way to the outer shell.” According to Pfost other factors also can lead to abnormal heat in the drum, such as a dragging brake and a duty cycle that’s too severe for the drum. Capps agrees. Heat cracks and drum discoloration are both signs of brake drum overheating. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA== 08Brake Inspections Tech Tip130007032019 “While cracks across the braking surface can be caused from improper installation, it is typically due to a thermal or mechanical overloading of the braking surface,” he says. “This can be due to various factors including: improper installation; inferior friction material; dragging brake, inadequate drum for the specific application; or parking brakes set while drum is overheated.” While mostly normal, there are times, according to Kay, when those small heat cracks may be signaling a problem. “With heat checks it’s okay to continue using the drum as they sometimes wear off over time or they do not grow,” Kay says. “It is important to note that heat checks would be expected to cover the drum 360 degrees and over the width of the shoe contact. This symptom indicates the shoe is in full contact when the brake is applied. “If the drum shows localized heat checking, for example in a certain section of the drum, then there may be a dimensional problem that is forcing contact in only one location,” he continues. “Sometimes the thermal stress will continue fatiguing the drum and larger cracks will develop. Once a larger crack forms then the drum must be replaced.” Beyond heat cracks look for drum discoloration as a sign of overheating. “If the brake surface has a blue color to it, this is typically a symptom of overheating,” Kay says. “Dragging brakes or simply over-using a brake can lead to excessive temperatures and as a result the drum turns blue from the oxidation.” Drum discoloration from heat damage may also result from martensite formation which leads to leopard spotting, Sturdy adds. Beating the drum about best practices Since it’s typically more time- and cost-effective to replace old drums with new ones, most shops have largely abandoned the process of turning drums. Penske, however, never took up the practice. “We have never turned drums and don’t see this as cost effective,” Hasinec says. “Turning drums creates additional down time for the vehicle. Turning drums has become somewhat rare and even finding a supplier that can do so can be a challenge. I believe most fleets have this same train of thought.” Pfost agrees. “The down time required to send a drum to be turned can be costly,” he says. “And if a drum is turned too far, it may still be in spec but by the time you wear out a new pair of shoes, it will no longer be in spec.” Sturdy says that the challenging aspects of drum turning have more shops opting for new drums over turning. “With the skills required to properly setup and align a brake drum on the pilot and mounting flange we are finding more shops are opting for replacement vs. turning,” he says. “Some sites that have consistent and proper maintenance programs we find them utilizing drums without having them turned, merely going from first lining to the second.” For those times when turning makes sense be sure to take the time to determine if the drum is a sound candidate. “Most manufacturers do not recommend resurfacing or turning a brake drum,” Capps says. “However, if turning is necessary, allow for at least .040 inches under the maximum diameter cast into the brake drum. For example, if the maximum diameter cast into the drum is 16.620 in., the maximum rebore limit should be 16.580 in.” When considering a drum for turning, be sure to select proper measurement points. “This should be measured at the worst location (any grooves or out of round for instance) to make sure sufficient material is there to remove,” Sturdy says. “Check the diameter of the braking surface at two points 90 degrees apart at the inner brake surface area and two on the outer brake surface to check for any roundness or taper issues. Checking in these four locations will help verify the drum diameter as well as any shape issues in the braking zone.” Brakes are only as good as their hardware, which means all related components also should be regularly inspected along with brake drums. Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==

08Air Brake System Cold Weather Operation Tips130012202018 TECH Tips Air Brake System - Cold Weather Operation Tips As the cold weather approaches, operators and fleets alike begin to look to their vehicles with an eye toward winterization, and particularly what can be done to guard against air system freeze-up. Here are some basic tips for operation in the cold weather. Engine Idling Avoid idling the engine for long periods of time. In addition to the fact that most engine manufacturers warn that long idle times are detrimental to engine life, winter idling is a big factor in compressor discharge line freeze-up. Discharge line freeze-ups account for a significant number of compressor failures each year. The discharge line recommendations shown under “Discharge Lines” are important for all vehicles, but are especially so when some periods of extended engine idling can not be avoided. Discharge Lines The discharge line should slope downward from the compressor discharge port without forming water traps, kinks, or restrictions. Cross-overs from one side of the frame rail to the other, if required, should occur as close as possible to the compressor. Dryer Inlet Temperature The dryer inlet air temperature should typically be within the range of no more than 160°F and no less than 45°F above low ambient (surrounding) temperature to prevent freeze-ups. (For example, if low ambient is minus 40°F, the dryer inlet must be above 5°F.) Lower dryer inlet temperatures should be avoided to minimize the risk of freeze-up upstream of the air dryer. Higher temperatures should also be avoided to minimize the risk of heat damage to the air dryer seals and to avoid a loss of drying performance. Compressor Line Size The line size and length is established by the vehicle manufacturer and should not be altered without the vehicle manufacturers approval. As a reference, the line length from the compressor to the air dryer should be less than 16 feet and the minimum line sizes should be as follows: Minimum Length Minimum I.D. Application 6 ft. 1/2 in. Low Compressor Duty Cycle Applications (0-20%) 10 ft. 5/8 in. High Compressor Duty Cycle Applications (20-40%) Line Insulation To guard against freeze-ups in low duty cycle applications, the discharge line can be insulated if it is greater than 9 feet in length. The line can only be insulated back to 9 feet and a maximum of 3 feet. For example, if the line is 10 feet in length, insulate the fitting and the last one foot of the line. If the line is 15 feet, insulate the fitting and the last 3 feet of the line. CATALOG NUMBER 08 www.midwestwheel.com Order NLINE ™ www.midwestwheel.com Order NLINE ™ Made with FlippingBook RkJQdWJsaXNoZXIy MTEyNjY3NA==